- ページ 4

投影スクリーン Draper SLX17のPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper SLX17 8 ページ。 230v ac scissor lift slx video projector lift
Draper SLX17 にも：パンフレット＆スペック (16 ページ), 設置および操作マニュアル (7 ページ), 据付・取扱説明書 (7 ページ), 据付・取扱説明書 (7 ページ)

ページを印刷する

Scissor Lift - SLX 115V

Section 3 - Adjusting for Level or Center of Gravity

Preferred Method—Adjusting Projector Pan

The Projector Pan can be moved forward or back.

1. Ensure Bottom Pan is supported.

2. Remove the Lifting Cable Bar.

3. Remove screws holding Projector Pan on Bottom Pan.

4. Move Projector Pan forward or back.

5. Replace screws.

6. Replace Lifting Cable Bar.

Secondary Method—Adjusting Lifting Cable Bar

1. Run unit to its "Service" position and ensure Bottom Pan is level.

2. Ensure Bottom Pan is not more than ¾"

not have to be perfectly level, as long as its positioning is consistent and repeatable

in "Show" and "Closed" positions.

3. Ensure Bottom Pan is supported.

4. Remove screws holding Lifting Cable Bar to the Projector Pan.

5. Move Lifting Cable Bar forward or back.

6. Replace screws.

7. Check level again. If still not level, repeat.

Section 4 - Installing Projector

Draper's optional Universal Projector Mount will hold up to 26 lb

See Installation Instructions included with Universal Projector Mount.

If not using Draper's Universal Projector Mount, generally the video projector

should be suspended from the bottom pan

according to projector manufacturer's instructions.

If installing with a small closure, maximum projector size is:

18" x 8¾"

(45.7 x 22.2 cm) (width x length x Environmental Air Space Housing height)

If installing with a large closure, maximum projector size is:

18" x 18"

(45.7 x 45.7 cm) (width x length x housing height)

When drilling initial holes for mounting projector, or if for any reason the hole

placement must be changed, completely lower lift before attempting to drill

holes. When attaching projector bracket to plate, make sure screws are short

enough that they do not touch the motor/roller above the plate when lift is

closed.

Unit and projection system should be operated, checked and adjusted as

necessary at this time

(see Sec. 8 for limit adjustment procedures)

CAUTION: Keep fingers & other objects away from ceiling closure when unit is operating. Serious injury or damage can result.

Section 5 - Attaching Universal Projector Mount to Projector Pan

Please Note: If unit is ordered with optional Universal Projector Mount pre-installed, disregard these instructions.

If unit is NOT ordered with optional Universal Projector Mount pre-installed, it is necessary to install a new Projector Pan, which includes the Universal Projector

Mount's rectangular plate.

1. Lower unit until the Bottom Pan is resting on a tabletop or other stable and sturdy surface.

2. Remove Lifting Cable Bar from Bottom Pan.

3. Remove bolts holding Projector Pan to Bottom Pan.

4. Remove Projector Pan and set aside.

5. Place new Projector Pan with Universal Mount into place.

6. Re-attach Projector Pan to Bottom Pan.

7. Re-attach Lifting Cable Bar to Bottom Pan.

Figure 4

(if above does not work)

out of level. However, the pan does

(19mm)

(12kg)

2 "

(64mm)

(100mm)

12"

(305mm)

2 "

(64mm)

12"

(305mm)

12"

(304mm)

page 4 of 8

5 "

(140mm)

10"

(254mm)

5 "

12"

(305mm)

(140mm)

10"

(254mm)

12"

(305mm)

(178mm)

2 "

(52mm)

(178mm)