投影スクリーン Draper TargaのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Targa 2 ページ。 Electrically operated projection screen with motor-in-roller
Draper Targa にも：取付・取扱説明書 (4 ページ), 取付・取扱説明書 (2 ページ), 取付・取扱説明書 (2 ページ), 取付・取扱説明書 (4 ページ), 取付・取扱説明書 (2 ページ), 取付・取扱説明書 (3 ページ), 設置および操作説明書 (4 ページ), 取付・取扱説明書 (2 ページ), 取付・取扱説明書 (2 ページ), 取扱説明書 (8 ページ)

ページを印刷する

Targa and Premier Electric Projection Screens—Large Sizes by Draper

➀ Read instructions through completely before proceeding.

➁ Follow instructions carefully. Installation con trary to instructions in val i dates

warranty.

➂ Screen should be accessible for complete removal should fabric be come

damaged or should other ser vice be required.

➃ Screen should be installed level (using a carpenter's level). The case must

also be installed so that the top of the case is level (front-to-back) to prevent

the fabric from contacting the case housing.

➄ Nothing should be fastened to screen dowel or viewing surface.

➅ Operating switch(es) packed separately in screen carton. Do not dis card

with packing material.

➆ Screen operates on 110-120V, 60 hz. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any re spon si bil i ty on

the part of Draper, Inc. for improper in stal la tion or faulty work man ship at the jobsite.

Hanging Screen

General:

Screen should be lifted into position only by the end mounting brackets.

Never attempt to lift screen along its length.

Installer must also insure that wall or ceiling structure is of adequate

strength. Supporting hardware must be essentially vertical. Do not suspend this

product using chain or cable (see note at bottom right regarding this screen

with Tork Star). The screen must be securely fastened using at least two of the

mounting holes provided in each of the case mounting brackets.

When locating view ing surface and checking clear ance for screen's op er a tion,

remember surface is centered in case. Handle case care ful ly to protect its ﬁ nish.

Regardless of mounting method, screen should be positively and securely

sup port ed so that vibration or even abusive pulling on the viewing surface will not

cause case to work loose or fall. Installer must insure that fas ten ers used are of

adequate strength and suit able for the mounting sur face cho sen.

Ceiling Installation:

Product is very heavy: Installer must provide adequate attachment hardware

and anchors as required. Installer must also insure that ceiling structure is of

adequate strength.

Wall Installation:

Product is very heavy: Installer must provide adequate attachment hardware

and anchors as required. Installer must also insure that wall structure is of

adequate strength.

Caution: Do not remove the roller assembly from the case unless neces-

sary for repairs. If the roller assembly is removed, be sure motor is fully

re-seated in the bracket, and re-secure it carefully with the motor retaining

spring and screw (see diagram below).

Screw is included

with Large Targas

and Large Premiers.

Please note: Do not use a power screwdriver to tighten screw.

Maximum torque for tightening screw is 5 lb-inches.

Electrical Connections

Screen operates on 110-120V, 60 Hz. current. Screen is shipped with internal

wiring complete and control switch(es) fully boxed, and standardly supplied with a 6'

cable lead. Longer lead can be substituted by removing two screws in motor end of

roller, removing lead, plugging new lead in, and replacing screws. Wire to connect

screen to switch(es) and switch(es) to power supply should be fur nished by installer.

Con nec tions should be made in ac cor dance with attached wiring diagram, and

wiring should comply with national and local electrical codes.

All operating switches should be "off" before power is connected.

Installation/Operating Instructions

Caution

Before fully operating screen: On Large Targa, remove tape; on Large Premier,

lower viewing surface enough to fully expose shipping brackets, then remove ship-

ping brackets by loosening screws, removing end shipping brackets, sliding center

shipping brackets off dowel, and re-tightening screws (see diagram).

110-120V Single Station Control — 3-position up-off-down switch per mits op er a-

tion to be stopped at any point. Factory adjusted limit switch es au to mat i cal ly stop

screen when fully down or fully up.

110-120V Multiple Station Control — Switches are similar in ap pear ance to

110-120V Single Station Control. Screen stops when switch is re leased and may be

re start ed in either direction. Factory adjusted limit switch es stop screen automati-

cally when fully up or fully down.

24V Control — Three-button up-stop-down switch es stop at any point de sired,

operate in any sequence. Factory adjusted limit switches au to mat i cal ly stop screen

when fully up or fully down.

Key Operated Switching — Two kinds of key-operated switches are op tion al ly

available with this unit. ➀ The key-operated power sup ply switch controls power to

the screen and switches. When it is "off ", the switch es will not operate screen. Key

may be re moved from the switch in either "on" or "off" position.

key switch per mits the screen to be operated directly by key. In this case, the

screen's operator must always have a key.

RS232/Ethernet — Serial communication and network communication optionally

available with wall switches, RF or IR remote.

Adjustments

Screen has been factory set and should not nor mal ly require further ad just ment.

However, if you desire to change the "up" and "down" stop ping po si tions, proceed

as follows:

CAUTION: Be sure all switches are in "off " position before ad just ing limit switch-

es. Always be pre pared to shut screen off man u al ly when new adjust- ment is being

tested. Screen may be se vere ly dam aged if viewing surface is al lowed to run too far

up or too far down.

Adjusting "fully up" position —You should never have to adjust this limit! If

you do, however, the "Up" stopping position may be ad just ed by turning the yellow

limit switch adjustment socket. The yellow socket is lo cat ed on left end of screen

roller and is accessible to a screwdriver/Allen wrench (4mm or

socket coun ter clock wise will allow the view ing surface to retract farther into the

case. Turn ing it clockwise will cause the sur face to stop farther out of the case. One

full revolution of the socket will alter the stop ping position of the view ing surface by

ap prox i mate ly 1½".

Adjusting "fully down" position — "Down" stopping position may be adjusted

by turning the white limit switch adjustment socket. The white socket is located on

the left end of screen roller and is accessible to a screw driv er/Allen wrench (4mm

"). Turning the socket coun ter clock wise will allow the viewing surface to run

farther down. Turning it clockwise will shorten the viewing surface, causing it to stop

in a less extended po si tion. At no time should viewing surface be unrolled enough to

expose any part of screen roller.

Targa

Use of Large Case Targa or Large Case Premier screens with TorkStar Utility Li-

neset requires specially modiﬁ ed Large Premier or Large Targa case and mount-

ing brackets. DO NOT use TorkStar with standard Large Case Targa or Premier

screen and brackets. Contact Draper for details.

If you encounter any difﬁ culties installing or ser vic ing your Targa or Premier screen, call

your dealer or Draper Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Operation

➁ A three-po si tion

"). Turn ing the

Premier

IMPORTANT