投影スクリーン Draper Targa 220VのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Targa 220V 2 ページ。 Electric

ページを印刷する

220V Targa Electric Projection Screen by Draper

These Installation/Operating Instructions are available in the official

language of the country where you purchase the product. Please contact your

distributor to request a copy.

Vous pourriez demander les instructions d'installation et d'opération

traduises dans la langue officielle du pays ou vous achetez le produit. Veuillez

demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der

offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben,

vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

Caution

➀ Read instructions through completely before proceeding.

➁ Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

➂ Screen should be accessible for complete removal should fabric become

damaged or should other service be required.

➃ Screen should be installed level (using a carpenter's level).

➄ Nothing should be fastened to screen dowel or viewing surface.

➅ Operating switch(es) packed separately in screen carton. Do not discard

with packing material.

➆ Screen operates on 220 V a.c., 50 Hz., 1 ph. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Hanging Screen

General: When locating viewing surface and checking clearance for screen's

operation, remember surface is centered in case. Handle case carefully to

protect its finish.

Regardless of mounting method, screen should be positively and securely

supported so that vibration or even abusive pulling on the viewing surface will

not cause case to work loose or fall. Installer must insure that fasteners used

are of adequate strength and suitable for the mounting surface chosen.

Suspended Installation:

Suspend screens from holes in endcaps as shown. S-hooks are included with

screen. Chains (or cable) and turnbuckles should be provided by installer.

Chains should be attached to beams or other structural members.

Turnbuckles should be adjusted so screen hangs level.

Wall Installation:

Mount screen through holes in back of endcaps as shown. No. 12 screws for

wood or aluminum are provided. However, if screen attaches to plaster,

gypsum board or masonry, installer should furnish toggle bolts, molly bolts,

nylon or lead anchors as required.

Recessed Installation:

Recess should permit access for removal of screen if necessary. Screen may

be mounted as in suspended or wall installation (see diagram on back page).

Fasteners for

wall mounting

by others.

" hole for

electrical

connection.

Mounting angle

and hardware

by others.

Suggested for

recessed installations.

Installation/Operating Instructions

S Hooks for

suspended installation.

Form Targa220V_Inst02

Printed in U.S.A.

Electrical Connections

Screen operates on 220 V a.c., 50 Hz., 1 ph. current.

Junction box is located inside left endcap and cover plate is secured to

endcap with two screws. Junction box contains terminal strip, per wiring

diagram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in accordance

with wiring diagram supplied, and wiring should comply with national and local

electrical codes.

All operating switches should be "Off" before power is connected.

Operation

Before operating screen remove tape securing fabric and dowel to roller. If

viewing surface hangs out of case 22 or 23 mm, tape has probably been

broken by rough handling in shipment, allowing surface to "unwrap" one turn

about the roller. Manually wrap fabric back around roller without turning the

roller itself.

Note: Drive unit contains a thermal overload protector. Operation as frequently

as six cycles per hour may trip the protector. If tripped, the protector should

reset automatically within a few minutes.

220 V a.c. Single Station Control— 3-position up-off-down switch permits

operation to be stopped at any point. Factory adjusted limit switches

automatically stop screen when fully down or fully up.

220 V a.c. Multiple Station Control (Not CE approved)—Switches are

similar in appearance to 220V Single Station Control. Screen stops when

switch is released and may be restarted in either direction. Factory adjusted

limit switches stop screen automatically when fully up or fully down.

24v Control —Three-button up-stop-down switch(es) stop at any point

desired, operate in any sequence. Factory adjusted limit switches

automatically stop screen when fully up or fully down. Installer should

incorporate an all-pole disconnect in the fixed wiring.

Key Operated Switching (Not CE approved)—Two kinds of key-operated

switches are optionally available with this unit. ➀ The key-operated power

supply switch controls power to the screen and switches. When it is "off", the

switches will not operate screen. Key may be removed from the switch in

either "on" or "off" position. ➁ A three-position key switch permits the screen to

be operated directly by key. In this case, the screen's operator must always

have a key.

Adjustments

Screen has been factory set and should not normally require further

adjustment. However, if you desire to change the "up" and "down" stopping

positions, proceed as follows:

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches. Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

Adjusting "fully up" position — "Up" stopping position may be adjusted by

turning the yellow limit switch adjustment socket.

the yellow socket is located on left end of screen roller and is accessible to a

screwdriver/Allen wrench (4mm or

will allow the viewing surface to retract farther into the case. Turning it

clockwise will cause surface to stop farther out of the case. One full revolution

of socket will alter stopping position of viewing surface by approximately 1½".

Adjusting "fully down" position — "Down" stopping position may be

adjusted by turning the white limit switch adjustment socket. The white socket

is located on the left end of screen roller and is accessible to a screwdriver/

Allen wrench (4mm or

"). Turning the socket counterclockwise will allow the

viewing surface to run farther down. Turning it clockwise will shorten viewing

surface, causing it to stop in a less extended position. At no time should

viewing surface be unrolled enough to expose any part of screen roller.

"). Turning the socket counterclockwise