- ページ 14

エアコン AirStage ASUB24RLAVのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。AirStage ASUB24RLAV 17 ページ。 Indoor unit (wall mounted type)
AirStage ASUB24RLAV にも：取扱説明書 (8 ページ)

ページを印刷する

7.3.1. Button name and function

OPERATION indicator lamp (Green)

TIMER indicator lamp (Orange)

FILTER indicator lamp (Red)

7.3.2. Checking the function settings

• Press and hold the "MANUAL AUTO" button on the indoor unit for 3 seconds to check

the function settings. It is necessary to disconnect the power in order to return to normal

operation mode.

(1) Indoor unit and refrigerant address indication

Indication pattern

Indicator name

Indoor unit address

OPERATION

indicator lamp (Green)

TIMER indicator

Address: tens place (0.5 s ON/0.5 s OFF)

lamp (Orange)

FILTER indicator

Address: ones place (0.5 s ON/0.5 s OFF)

lamp (Red)

• Indoor unit address example

(Example) ADDRESS : 24

OPERATION

indicator lamp

(Green)

OFF

TIMER

indicator lamp

0.5s 0.5s 0.5s 0.5s

(Orange)

OFF

FILTER

0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s 0.5s

indicator lamp

OFF

(Red)

• Refrigerant address example

(Example) ADDRESS : 30

OPERATION

indicator lamp

1.0s

(Green)

OFF

TIMER

indicator lamp

0.5s 0.5s 0.5s 0.5s 0.5s 0.5s

(Orange)

OFF

FILTER

indicator lamp

OFF

(Red)

• Setting details

Function

number

Indoor unit address

Refrigeration address

For use with a remote control, set all rotary switches to 0, and refer to "7.1. Setting the ad-

dress" for details.

All switches are set to 0 at the factory.

(2) Others

Indication pattern

Indicator Name

OPERATION indicator lamp (Green)

TIMER indicator lamp (Orange)

FILTER indicator lamp (Red)

En-13

Indication pattern

Refrigerant address

Flash (1.0 s ON/1.0 s OFF)

1 cycle 12 sec

10 sec

8 sec

1 cycle 12 sec

1.0s

9 sec

OFF

Item

Setting number

00~63

00~99

Indication pattern

Function number; tens place (0.5 s ON/0.5 s OFF)

Function number; ones place (0.5 s ON/0.5 s OFF)

Setting number: (0 - 9) (0.5 s ON/0.5 s OFF)

(Example) Function : 31, Setting number : 2

OPERATION

indicator lamp

0.5s

0.5s 0.5s 0.5s

(Green)

OFF

TIMER

indicator lamp

0.5s 0.5s

(Orange)

OFF

FILTER

0.5s

indicator lamp

(Red)

OFF

8. FINISHING

Before performing this section, perform a sealing test. (Refer to the installation Manual for

the outdoor unit.)

] 1

8.1. Connection pipe, cable and drain hose

Insulate the drain hose, if necessary, to prevent it from freezing.

(1) Insulate between pipes.

• For

Rear,

Right and

Bottom piping, overlap the connection pipe heat insulation

and indoor unit pipe heat insulation and bind them with vinyl tape so that there is no

gap.

• For

Left bottom piping,

Left piping,

the connection pipe heat insulation and indoor unit pipe heat insulation together and

bind them with vinyl tape so that there is no gap.

( 1 Rear, 2 Right and 3 Bottom piping)

Overlap the insulation.

Connection pipe

(heat insulation)

Bind the pipes together so

that there is no gap.

(For

Left bottom piping,

Left piping,

• Wrap the area which accommodates the rear piping housing section with cloth tape.

• Bind the connection cable with vinyl tape.

• Bundle the piping and drain hose together by wrapping them with cloth tape over the

range within which they ﬁ t into the rear piping housing section.

Connection pipe

Cloth tape

(Accessories)

Connection cable (Power supply cable)

Vinyl tape

Connection cable (Transmission and Remote controller cable)

Wrap with cloth tape

Pipe

Cloth tape

Drain hose

(2) Temporarily fasten the connection cable along the connection pipe with vinyl tape.

(3) Fasten the connection pipe to the outside wall with a saddle, etc.

(4) Fill the gap between the outside wall pipe hole and the pipe with sealer so that rain

water and cannot blow in.

(5) Fasten the drain hose to the outside wall, etc.

1 cycle 12 sec

9 sec

11 sec

10 sec

Center piping and

Left rear piping, butt

Indoor unit pipe (heat insulation)

Vinyl tape

Center piping and

Left rear piping)

Indoor unit pipe

Wrap with cloth tape.

Pipe