- ページ 5
室内装飾品 Draper FlexShadeのPDF インストレーション＆オペレーションマニュアルをオンラインで閲覧またはダウンロードできます。Draper FlexShade 8 ページ。 Exterior clutch-operated shade
Draper FlexShade にも： インストレーション・インストラクション (2 ページ), 取扱説明書 (12 ページ), 取付・取扱説明書 (11 ページ), 説明書 インストールと操作 (12 ページ), 説明書 インストールと操作 (16 ページ), 説明書 インストールと操作 (4 ページ), 取扱説明書 (7 ページ), 説明書 インストールと操作 (12 ページ), 説明書 インストールと操作 (16 ページ)
ページを印刷する
Motorized FlexShade
Section 5 - Electrical Connections
Shade operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch(es) fully boxed, and standardly supplied with a
6' cable lead. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to
connect shade to switch(es) and switch(es) to power supply should be furnished by installer. Connections should be made in accordance with attached wiring
diagram, and wiring should comply with national and local electrical codes. DO NOT wire motors in parallel without written permission from Draper.
All operating switches should be "off" before power is connected.
Please Note: For low voltage wiring requirements, Draper recommends consulting with a professional low voltage electrical contractor.
It is very important that shielded and stranded CAT 5 cable be used to prevent any electrical interference.
Section 6 - Limit Switch Adjustments
Section 6.1 - Standard and Quiet Motors
Caution: Be sure all switches are in "off" position before adjusting limit switches. Always be prepared to shut off manually when new adjustment is being
tested. Do not allow the shade roller to become exposed by running the shade fabric too far down. Shade may be severely damaged if allowed to
run too far up or down. Each shade's limit switch must be set if using group control system. Motor should be installed so limit switches are pointed
down or accessible.
Section 6.1.1- Push Button Limits
1. Fully depress both limit switch push buttons, then operate wall switch to make sure system works properly.
2. Raise shade to desired "up" stop position.
3. Set upper limit by depressing and releasing the proper (back) push button.
4. Lower shade to desired "down" stop position.
5. Set lower limit by depressing and releasing the proper (front) push button.
Section 6.1.2 - Screw-Type Limits
1. Determine which direction of fabric travel corresponds with arrows on motor.
2. Operate shade to desired "down" stop position.
Set limit by turning the proper socket toward the "+" to lower the limit, and "-" to raise it.
3. Operate shade to desired "up" stopping position.
Set limit by turning the proper screw toward the "-" to raise the limit, and "+" to lower it.
Section 6.2 - Limit Adjustments (485 Motors)
1. Connect the 485 switch to the motor via the terminal blocks, or via the modular port using four conductor modular cable.
When using modular cable, the cable connectors MUST NOT be crimped in reverse, as with standard telephone cable.
2. Set the slide switch to the lower position. Press and hold the DOWN button on the switch to move
the viewing surface to the desired lower limit. If the shade moves in the opposite direction, release
the DOWN button and press and hold down the STOP button for four seconds. This will reverse
the operation of the UP and DOWN switches.
3. Move slider switch into center position. Wait a couple of seconds.
Please Note: If you move the slider switch from down to up in one motion it sets the two limits in the same postion.
4. Set the slide switch to the higher position. Move the shade to the desired upper limit by pressing and
holding the UP button on the wall switch.
5. Return the slide switch to the center position to return to normal operation.
6. To set the shade to an intermediate position, move the shade to the desired position and press the
STOP button. Press and hold the STOP button for at least three seconds to record the position.
Please Note: Pressing and releasing the UP button on the switch will move the shade to its upper limit.
Pressing and releasing the DOWN button will move the shade to its lower limit.
While the motor is in motion, pressing the STOP button for less than two seconds will stop the shade
at its present position.
Once the motor is stopped, pressing the STOP button will move the shade to its intermediate position.
Pressing and holding the STOP button, when the motor is at rest or in motion, for at least three seconds
will record a new position.
Section 6.3 - Limit Switch Adjustments—RTS Motors
For limit setting instructions on these motors, see Draper's RFRC_Motor_Prog_Inst available in the motorized shades section of www.draperinc.com.
®
page 5 of 8
Front
(Yellow)
Back
(White)
PUSH BUTTON LIMITS
Bottom View
Front
(Yellow)
Back
Side View
(White)
+
Bottom View
Front
(Yellow)
SCREW-TYPE LIMITS
Back
(White)
Bottom View
+
Screws
Front
Side View
(Yellow)
Back
+
(White)
Side View
Bottom View
Figure (8)
Screws
FUNCTION
POSITION
Side View
Set LOWER limit
DOWN
Set UPPER limit
UP
Normal Operation
CENTER
Back View of Wall Switch
To Motor
with
Built-In
Low Voltage
Slide
Switch
C
o
m
+
m
5V
o
To Motor
DC
n
with
Built-In
Low Voltage
+
D
o
U
w
p
n