- ページ 8
室内装飾品 Draper LightBloc ZIP 127のPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper LightBloc ZIP 127 12 ページ。
ページを印刷するLightBloc ZIP™ 92 & ZIP 127
Section 9 - Limit Setting: Standard and Quiet Motors
Caution: Unit ships without limits. Limits will need to be set
before the unit is operated. Always be prepared to shut off
manually when new adjustment is being tested.
Push Button Limits
1. Fully depress both limit switch push buttons, then
operate wall switch to make sure system works properly.
2. Raise shade to desired "UP" stop position.
3. Set upper limit by depressing proper
push button.
(back)
4. Lower shade to desired "DOWN" stop position.
5. Set lower limit by depressing proper
Screw-Type Limits
6. Determine which direction of fabric travel corresponds
with arrows on motor.
7. Operate shade to desired "down" stop position.
Set limit by turning proper socket toward "+" to lower limit, and "-" to raise it.
8. Operate shade to desired "up" stopping position.
Set limit by turning proper screw toward "-" to raise limit, and "+" to lower it.
Please Note: Each full rotation of the limit screw equals approximately
5/ 8 "
of shade travel, which may require rotating the limit screw
(16mm)
several times.
Caution: DO NOT allow the hem bar to hit the upper roller or fascia.
This will damage the unit.
Caution: DO NOT allow hem bar to retract into the headbox.
Section 10 - Complete Electrical Connection
Operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch
. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to connect
(standard)
shade to switch
and switch
(es)
(es)
wiring should comply with national and local electrical codes.
DO NOT wire motors in parallel without written permission from Draper
All operating switches should be "off" before power is connected.
Controls & System Overview
Sonesse
RTS 120VAC Motors
®
RTS
MOTOR
120V
B
W
G
110-120V Line
Dashed Wiring
by Electrician
Sonesse
is a registered trademark of Somfy
®
push button.
(front)
to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and
Patio
RF Remote
STOP
Decora RTS
Wireless Keypad
Systems, Inc.
®
Caution:
- Be sure all switches are in "off"
position before adjusting limit
switches.
- Shade may be damaged by
running shade fabric up too far
and exposing roller.
- If using a group control system,
each limit switch must be set
prior to connecting to system.
- Motor must be installed so
limit switches are pointed up or
accessible.
fully boxed, and supplied with a 6'
(es)
.
®
Controls & System Overview
Sonesse
W
110-120V Line
ROOM SIDE
Front
Back
GLASS SIDE
PUSH BUTTON LIMITS
ROOM SIDE
ROOM SIDE
Front
Front
Back
Back
GLASS SIDE
Bottom View
GLASS SIDE
SCREW-TYPE LIMITS
ROOM SIDE
+
ROOM SIDE
Front
Side View
+
Front
Back
+
Screws
Back
GLASS SIDE
+
Bottom View
GLASS SIDE
Bottom View
Screws
Side View
Screws
Side View
(183 cm)
120VAC Motors
®
NOTE: Test shade operation
120V
If shade direction does not
MOTOR
correspond with the switch
orientation, turn power back
red
and black
off and switch the
wires from the motor to the switch.
Do not wire motors in parallel without
written permission from Draper.
B
R
G
Control
Switch
Single Gang
B
Box (by others)
Dashed Wiring
by Electrician
page 8 of 12
Standard right-hand
Bottom View
motor configuration shown
+
+
Side View
Standard right-hand
Bottom View
motor configuration shown
Side View
cable lead