- ページ 4

室内装飾品 Draper Motorized FlexShadeのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Motorized FlexShade 8 ページ。 Motor operated window shades with several control options
Draper Motorized FlexShade にも：取扱説明書 (12 ページ)

ページを印刷する

Motorized FlexShade

Section 4.2 - Attaching Fascia to Endcaps

1. Place groove along top of fascia over endcaps, and snap into place

Endcaps must be installed the correct distance apart for fascia to be properly attached

with full engagement. Fascia is not fully seated until it clicks into place on both ends.

Once in place, check for secure fit. If not secure, secure with appropriate fastener

Section 4.3 - Reverse Roll Fascia

1. Slide endcaps into extrusions.

2. Using provided holes in endcaps, mark the fascia for drilling.

3. Attach endcaps to fascia.

4. Mount Endcaps/Reverse Roll Fascia.

5. Install roller/fabric/operator assembly according to relevant instructions.

6. Attach endcap covers to endcaps. Use double-sided tape to help secure in place.

Section 5 - Surface Headbox or Pocket Headbox

1. Snap endcap covers onto endcaps.

2. Slide endcaps into the top/back portion of surface headbox or into pocket extrusion

of large pocket headbox. Using provided holes in endcaps, mark headbox for drilling.

Please Note: The installer is responsible for selecting mounting hardware appropriate for site conditions.

Caution: Before mounting shades, verify measurements on the provided with shade,

and ensure endcaps are installed at correct width.

3. Drill holes in back

(wall mount)

4. Attach endcaps and Surface Headbox back/top or Large Pocket Headbox extrusion to wall,

ceiling or pocket using mounting hardware appropriate for site conditions.

5. Install shade

(See Section 4.1 - Mounting Endcaps for Fascia)

6. Attach headbox fascia or pocket closure

Note on surface style headbox:

Fascia is not fully seated until it clicks into place on both ends. Once in place,

check for secure fit. If not secure, secure with appropriate fastener

Section 6 - Electrical Connections

Shade operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch

6' cable lead. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to

connect shade to switch

and switch

(es)

diagram, and wiring should comply with national and local electrical codes. DO NOT wire motors in parallel without written permission from Draper.

All operating switches should be "off" before power is connected.

Please Note: For low voltage wiring requirements, Draper recommends consulting with a professional low voltage electrical contractor.

It is very important that shielded and stranded CAT 5 cable be used to prevent any electrical interference.

Please Note: A Draper Motor Test Cable

(See Section 4.2 - Attaching Fascia to Endcaps Step 1)

or top

(ceiling mount)

, of or in a pocket.

(see Fig. 7)

to power supply should be furnished by installer. Connections should be made in accordance with attached wiring

(es)

(Part# 503109)

and M12 Pigtail

(see Fig. 5)

(not included)

Large Pocket Headbox

STEP 1

STEP 2

(not included)

STEP 3

(Part# C107.089.60)

are recommended for temporary power for testing and limit setting.

page 4 of 8

Fascia Attachment Small & Large Endcaps

ATTACHING FASCIA

STEP 2:

STEP 1:

ENDCAP

Clicks into place

Figure 5

Figure 6

ATTACHING CLOSURE PANEL

Small Pocket Headbox

Large Pocket Headbox

STEP 1

STEP 2

STEP 3

Secure to Endcap

with Screw

Figure 7

fully boxed, and standardly supplied with a

(es)

Small Pocket H

STEP 1

STEP 2

STEP

STEP 3

Secure to E

with Screw