- ページ 23

オーブン Bosch CMG7361B1BのPDF ユーザーマニュアルと設置手順をオンラインで閲覧またはダウンロードできます。Bosch CMG7361B1B 48 ページ。

ページを印刷する

Basic setting

Wi-Fi

Remote control status Monitoring

17.3 Operating the appliance with the

Home Connect app

You can use the Home Connect app to set and start

the appliance remotely.

WARNING ‒ Risk of fire!

Combustible objects that are left in the cooking com-

partment may catch fire.

Never store combustible objects in the cooking

▶

compartment.

If smoke is emitted, the appliance must be switched

▶

off or the plug must be pulled out and the door

must be held closed in order to stifle any flames.

Requirements

¡ The appliance is switched on.

¡ The appliance is connected to the home network

and to the Home Connect app.

¡ In order to be able to set the appliance via the app,

the manual or permanent remote start must be se-

lected in the "Remote control status" basic setting.

To activate remote start, press ⁠ .

Configure a setting in the Home Connect app and

send it to the appliance.

Notes

¡ If you open the appliance door within 15 minutes

of activating remote start or of the operation end-

ing, the manual remote start is deactivated.

¡ When you start the oven using the controls on

the appliance itself, the remote start function is

activated automatically. You can use the

Home Connect app to adjust the settings or start

a new programme.

17.4 Software update

Your appliance's software can be updated using the

software update function, e.g. for the purposes of op-

timisation, troubleshooting or security updates.

To do this, you must be a registered Home Con-

nect user, have installed the app on your mobile device

and be connected to the Home Connect server.

As soon as a software update is available, you will be

informed via the Home Connect app and will be able to

start the software update via the app. Once the update

has been successfully downloaded, you can start in-

Possible settings

Off

Manual remote start

Permanent remote start

Explanation

You can use the Wi-Fi to switch off the network connection for

your appliance. When you have connected successfully once,

you can deactivate the Wi-Fi and not lose your detailed data.

As soon as you activate Wi-Fi again, the appliance connects

automatically.

Note: In networked standby mode, the appliance requires a

maximum of 2 W.

During monitoring, you can only view the operating status of

the appliance in the app.

For manual remote start, you must activate the remote start

each time before you can start the appliance via the app. If

you open the appliance door within 15 minutes of activating

remote start or of the operation ending, remote start is deactiv-

ated.

For permanent remote start, you can start and operate the ap-

pliance remotely at any time. If you often operate the appliance

remotely, it is helpful to set the remote start to "Permanent".

stalling it via the Home Connect app if you are in your

WLAN home network (Wi-Fi). The Home Connect app

will inform you once installation is successful.

Notes

¡ You can continue to use your appliance as normal

while updates are downloading. Depending on your

personal settings in the app, software updates can

also be set to download automatically.

¡ We recommend that you install security updates as

soon as possible.

¡ Installation takes a few minutes. You cannot use

your appliance during installation.

17.5 Remote diagnostics

Customer Service can use Remote Diagnostics to ac-

cess your appliance if you contact them, have your ap-

pliance connected to the Home Connect server and if

Remote Diagnostics is available in the country in which

you are using the appliance.

Tip: For further information and details about the avail-

ability of Remote Diagnostics in your country, please

visit the service/support section of your local website:

www.home-connect.com.

17.6 Data protection

Please see the information on data protection.

The first time your appliance is registered on a home

network connected to the Internet, your appliance will

transmit the following types of data to the

Home Connect server (initial registration):

¡ Unique appliance identification (consisting of appli-

ance codes as well as the MAC address of the Wi-Fi

communication module installed).

¡ Security certificate of the Wi-Fi communication mod-

ule (to ensure a secure data connection).

¡ The current software and hardware version of your

appliance.

¡ Status of any previous reset to factory settings.

This initial registration prepares the Home Connect

functions for use and is only required when you want to

use the Home Connect functions for the first time.

Home Connect en