- ページ 12
オーブン Bosch CSG656R.1AのPDF ユーザーマニュアルとインストール手順をオンラインで閲覧またはダウンロードできます。Bosch CSG656R.1A 48 ページ。
ページを印刷する
en Before using for the first time
7 Before using for the first time
Implement the settings for the initial configuration. Calibrate the appliance. Clean the appliance and accessories.
7.1 Before using for the first time
Before using the appliance for the first time, ask your
water supplier about the hardness of your tap water. To
ensure that the appliance can reliably remind you to
descale it when required, you must set your water hard-
ness range correctly.
ATTENTION!
If the wrong water hardness has been set, the appli-
ance cannot remind you to descale it at the right time.
Set the water hardness correctly.
▶
Using unsuitable liquids may damage the appliance.
Do not use distilled water, highly chlorinated tap wa-
▶
ter (>40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or
▶
non-carbonated mineral water.
Setting
1
00 (softened)
01 (soft)
02 (med.)
03 (hard)
2
04 (very hard)
Only set this if you will be using solely softened water.
1
Also set for mineral water. Only use non-carbonated mineral water.
2
7.2 Initial configuration
When the appliance is connected to the electricity sup-
ply for the first time or following a lengthy power cut,
you need to configure the settings before you can use
it. It may take a few seconds for the settings to appear
in the display.
Press the text field for the required setting.
1.
Possible settings:
– Language
– Clock
– Water hardness
Turn the control ring to change the setting as re-
2.
quired.
Finally, press "Complete the settings" to confirm.
3.
a A note appears in the display confirming that the ini-
tial configuration is complete.
a The time that is set appears on the display.
To check the appliance before heating for the first
4.
time, open and close the appliance door once.
12
Malfunctions may occur when using filtered or deminer-
alised water. The appliance may request that you top
up the water tank even though it may be full, or opera-
tion with steam is cancelled after approx. two minutes.
▶
Tip: If you use mineral water, set the water hardness
range to "very hard". If you use mineral water, you must
only use non-carbonated mineral water.
Tip: If your tap water is very hard, we recommend that
you use softened water. If you use only softened water,
you can set your appliance to the "softened" water
hardness range.
Water hardness in
mmol/l
-
Up to 1.5
1.5–2.5
2.5–3.8
Above 3.8
7.3 Calibrating and cleaning the appliance
before using it for the first time
You will need to calibrate the appliance and clean the
cooking compartment and accessories before using it
to prepare food for the first time.
Note: The boiling point of water depends on the air
pressure. When calibrating, the appliance self-adjusts
during the first steaming operation to the pressure ratio
at the installation location.
Do not open the appliance door while calibration is in
progress as this will abort the calibration process.
Requirement: The cooking compartment is cold or at
room temperature.
1.
2.
3.
4.
5.
If required, mix filtered or demineralised water with
the bottled non-carbonated mineral water with a ra-
tio of one to one.
German hardness in
°dH
-
Up to 8.4
8.4–14
14–21.3
Above 21.3
Remove the product information and the accessor-
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
the adhesive tape that is in or on the appliance.
Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
Press
to switch the appliance on.
Fill the water tank.
→ "Filling the water tank", Page 16
Apply the following settings:
Type of heating
Temperature
Cooking time
→ "Basic operation", Page 13
French hardness °fH
-
Up to 15
15–25
25–38
Above 38
Steaming
100 °C
30 minutes