- ページ 2

アクセサリー BD Sensors DL01のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。BD Sensors DL01 2 ページ。 Digital gauge

ページを印刷する

5.1 Data logger

The battery powered digital gauge disposes of an integrated data

logger. The measuring values stored away in the device can be

selected above the communication interface by means of

software BD|LOG (included in delivery).

5.2 PC - connection

Connect

device

with a computer as follows:

unscrew the protective screwing of the communication

interface with a suitable slit screwdriver.

connect the handle plug of the connecting cable (included

in delivery) with the interface socket of the device. Con-

nect the side with the USB plug with a free USB connec-

tion on the computer.

install the COM driver and data logger software BD|LOG,

receive available on CD (included in delivery).

after the use, disconnect the connection and lock the

protection screwing again properly.

6. Initial start-up

remove the insulation foil before first

WARNING! Before start-up, the user has to check for

proper installation and for any visible defects.

WARNING! The device can be started and operated by

authorized personnel only, who have read and understood

the operating manual!!

WARNING! The device has to be used within the technical

specifications, only (compare the data in the data sheet)!

7. Placing out of service

WARNING! When dismantling the device, it must always be

done in the depressurized and currentless condition! Check

also if the medium has to be drained off before dismantling!

WARNING! Depending on the medium, it may cause

danger for the user. Comply therefore with adequate

precautions for purification.

8. Operation

8.1 Operating and display elements

barograph

timer / battery

time

display

pressure value

right button

left button

menu - button

temperature

Fig. 4 Display and operating foil

The display of the measuring value as well as configuring the

single parameters occurs menu-steered about a LC display

capable of graphic arts. The single functions are regulated on the

basis of three-front-sided arranged push buttons.

The menu system is closed, thereby one can "browse" forward

as well as backward by the single setting menus to reach to the

desired setting point.

8.2 Structure of the menu system

7.3 Menu list

Switch on

Menu 1/9

on / off

Menu 2/9

date / time / info

Menu 3/9

Units

Menu 4/9

Min / Max Values

introduction.

Menu 5/9

Configuration 1

Menu 6/9

Configuration 2

Menu 7/9

Backlight

Menu 8/9

Data Logger

Menu 9/9

Sensor Data

Error

- Left Button:

- Right Button: if is a functional button and can be configured in the menu 6. Light-, Zero-, Reset- or Max- function can

- Menu-Button: by pressure of this button "menu" you reach in the operating mode; moreover, she serves for the choice

To the configuration of the single menu points the desired menu point is to be put with the help of the left button "<<" or right

button ">>". Confirm this afterwards with the menu button "Edit" the menu point is marked and the configuration can begin.

To store an opposed value the menu button "Next" must be also pressed. To leave the menu press the menu button so often

to the mark of the single menu point and choose with the left button "<<" or right button ">>" the menu 1 and press the menu

button once more "Exit". The operating mode will also leave after approx. 1 min automatically.

Changes become first after activity of the menu button "Next" and after abandonment of the menu point effective. With

the abandonment of the whole menu system the opposed parameters are checked once again in dependence to each

other and concerning the characteristics of the device. With the configuration of the unity a conversion of the measuring

area occurs in the new unity only after abandonment of the menu system. According to pressure area not all units can be

also used if necessary.

9. Maintenance

In principle, this device is maintenance-free. If desired, the

housing of the device can be cleaned when switched of using a

damp cloth and non-aggressive cleaning solutions.

With certain media, however, the diaphragm may be polluted or

coated with deposit. It is recommended to define corresponding

service intervals for control. After placing the device out of

service correctly, the diaphragm can usually be cleaned carefully

with a non-aggressive cleaning solution and a soft brush or

sponge. If the diaphragm is calcified, it is recommended to send

the device to BD SENSORS for decalcification. Please read

therefore the chapter "Repair" below.

A false cleaning of the device can cause an irreparable

damage on the diaphragm. Therefore never use pointed ob-

jects or pressured air for cleaning the diaphragm.

11. Service / Repair

We recommend that the instrument is regularly recalibrated by

BD SENSORS, with timeintervals of approx. 12 months.

Before you return, the device has to be cleaned carefully and

packed shatter-proofed. You have to enclose a notice of return

with detailed defect description when sending the device. If your

device came in contact with harmful substances, a declaration of

decontamination is additionally required. Appropriate forms can

be downloaded from our homepage www.bdsensors.com.

Should you dispatch a device without a declaration of

decontamination and if there are any doubts in our service

department regarding the used medium, repair will not be started

until an acceptable declaration is sent.

The device can be switched on with every button (left button, menu button, right button).

By push the menu button the operating mode will be selected / left / ("Menu" / "Exit").

Setting of topical time and the topical date. Software version will be showed.

Setting of the pressure unit

adjustable units: [bar], [mbar], [PSI], [inHg], [cmHg], [mmHg], [hPa], [kPa], [MPa], [mmH2O], [mH2O], [kg/cm

or [user] (the user-defined unit can be programmed only by means of the software BD|LOG), a conversation of

all pressure related parameters is carried out automatically

Setting of decimal places

adjustable decimal place: standard [Std], [+1], [+2]

Setting of the temperature unit

the unity is not adjustable. Factory setting [°C]

Displaying of Min / Max Values

- Minimum pressure display: The minimum pressure applied during measuring is shown in the display.

min

- Maximum pressure display: The maximum pressure applied during measuring is shown in the display.

max

- Maximum pressure display: The minimum temperature during measuring is shown in the display.

min

- Maximum temperature display: The maximum pressure applied during measuring is shown in the display.

max

Possible options: reset value [Reset ?]

(Resetting of a value: select the menu point with "Edit" → button ">>" operate. There appears the question "Reset?" → once more

operate the button ">>". It seems "Sure?" additional confirmation whether the value should be put back → repeated confirming with the

button ">>" takes over topically adjoining pressure as a minimum value.)

Language:

Setting of user languages German [DE] or English [EN]

Measuring rate: here it is put how often the measurement is carried out and is indicated.

Possible settings are: a measurement per second [1/sec]

or two measurements per second [2/sec]

Auto Off Time:

Setting of the automatic switch off in minutes. The automatic switch off is able in steps from

[1 min], [2 min], [3 min], [4 min] or [5 min]; 30 seconds before switching off the timer is

activated and indicated in the display.

By the option [Off] the device can be deactivated. After deactivation, the precision digital

gauge is in the continuous operation.

Button settings: left button / right button

Left Button:

function configurations: [Min], [Light], [Zero], [Reset]

Right Button:

function configurations: [Max], [Light], [Zero], [Reset]

Function descriptions:

- [Min] / [Max]

- [Light]

- [Zero]

- [Reset]

Damping:

the damping can be put in 1 second steps between [1 sec] and [10 sec] or be

deactivated by option [Off]

Backlight settings of display

On Time:

the backlight duration can be put in 1 second steps between [1 sec] and [10 sec] or be

deactivated by option [Off]

Brightness:

the brightness can be put into 5% of steps between [0%] and [100%]

Data Logger configuration

Data Logger:

the following settings are possible: linearly [Linear] (value admission to the counter level 8500

is reached), cyclically ( [Loop] (after the value is reached in 8500, the data logger automatically

begins the values once more to grasp and, besides, headlines the old values) or [Off]

(in the display appears

Interval:

Intervals to the memory of the measuring values (pressure / temperature) second [1-99 sec],

minute [1-99 min], hour [1-99 hour] or day [1-99 days]

Time:

Measuring value admission: in which time the measuring value admission should occur (is

only efficiently for the setting "daily").

Counter:

Number of the grasped measuring values is indicated. Maximum value: 8500

(Put back counter reading: menu point with "Edit" select → button "Next" four times operate → button ">>" operate. There appears the

question "Reset?" → once more operate the button ">>". It seems "Sure?" additional confirmation whether the value should be reset →

repeated confirming with the button ">>" reset the grasped measuring values. Display announcement "Counter: 0/8500")

[SN:]

the standard number is indicated

[Lower]

Measuring area beginning

Values are put by factory and are not adjustable.

Display "No Sensor": display and pressure sensor module are separated.

if is a functional button and can be configured in the menu 6. Light-, Zero-, Reset- or Min- function can be

assigned to the button. The configured function is active in the display mode. Hold the button during

approx. 2 seconds to activate the function. In the operating mode you move in the menu system back-

ward "<<" or you reduce the set value.

be assigned to the button. . Hold the button during approx. 2 seconds to activate the function. In the op-

erating mode you move in the menu system forward ">>" or you raise the set value.

of the single menu points "Edit" or in the confirmation the opposed worth "Next".

minimum / maximum pressure value will be showed

the display backlight is activated

the zero point is automatically put, in the display appears

the opposed zero is put back,

goes out

if the data logger is activated and goes out if the data logger is off)

[Upper]

Measuring area end

[Date]

Production date

If the device came in contact with hazardous sub-

stances, certain precautions have to be complied with

for purification!

12. Disposal

The device must be disposed according to the

European Directives 2002/96/EG and 2003/108/EG

(on waste electrical and electronic equipment)

Waste of electrical and electronic equipment may

not be disposed by domestic refuse!

WARNING! Depending on the measuring medium, deposit

on the device may cause danger for the user and the

environment. Comply with adequate precautions for

purification and dispose of it properly.

13. Warranty conditions

The warranty conditions are subject to the legal warranty period

of 24 months from the date of delivery. In case of improper use,

modifications of or damages to the device, we do not accept

warranty claims. Damaged diaphragms will also not be accepted.

Furthermore, defects due to normal wear are not subject to

warranty services.

14. Declaration of conformity / CE

The delivered device fulfils all legal requirements. The applied

directives, harmonised standards and documents are listed in the

EC declaration of conformity, which is available online at:

http://www.bdsensors.com/products/ download/certificates.

Additionally, the operational safety is confirmed by the CE sign

on the manufacturing label.

]

BA_DM0X_E_210217