- ページ 28

洗濯機 Electrolux EPPWESGFBのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Electrolux EPPWESGFB 28 ページ。

ページを印刷する

Long idle periods

Whenever the appliance is not going to be used for a

long period of time (e.g. one month), carefully carry out

the following instructions.

•

Close the water supply cock.

•

Completely drain the tank and carry out a cleaning

cycle (see instructions in the paragraph J8.1 "End

of service and daily internal cleaning")

•

Remove and carefully clean the filters.

•

Completely drain

hoses, removing them from the containers. Repeat

the procedure described in the paragraph "Manual

activation" at least 3 times.

•

Completely drain the boiler by simultaneously

pressing the buttons as shown in the figure



•

A buzzer indicates completion of drainage.

•

Clean the inside and outside of the appliance as

indicated in par. J8.1 "End of service and daily

internal cleaning" and J8.2 "Exterior cleaning".

•

Spread a film of paraffin oil over the steel surfaces.

When using the appliance again, follow the indications

in par. J4 "Daily activation of appliance".

J10

Maintenance

Inspection and maintenance intervals depend on the

actual appliance operating conditions (total wash

hours) and ambient conditions (presence of dust,

damp, etc.), therefore precise time intervals cannot be

given. In any case, to minimize interruptions of the ser-

vice, careful and periodical appliance maintenance is

advisable.

Therefore, it is advisable to:

•

Descale the boiler, inside surfaces of the tank and

the appliance piping once or twice a year (call tech-

nical assistance).

•

Every month descale the wash and rinse jets with

vinegar or scale remover.

•

The internal hose of the rinse-aid and detergent

peristaltic dispenser should undergo periodic main-

tenance (once or twice a year).

•

Clean the water filter installed on the supply inlet

pipe, and the solenoid valve protection filter at least

twice a year (call technical assistance).

It is also advisable to stipulate a scheduled pre-

ventive maintenance contract with technical assis-

tance.

the incorporated dispenser

J10.1 Preventive maintenance

The preventive maintenance call can be activated (call

technical assistance).

On reaching the set number of cycles (e.g. 20000), a

technical assistance call message appears on the dis-

play.

This message suggests calling a specialized techni-

cian, for a general check of the equipment.

J11

Appliance disposal

At the end of the product's life cycle, make sure the

equipment is not dispersed in the environment. The

equipment must be disposed of in compliance with

current regulations in the country of use.

All metal parts are in s/steel (AISI 304) and removable.

Plastic parts are marked with the letters of the material.

The symbol

on the product indicates that this

product should not be treated as domestic waste, but

must be correctly disposed of in order to prevent possi-

ble negative consequences for the environment and

the human health.

Regarding the recycling of this product, please contact

the sales agent or dealer of your product, your after-

sales service or the appropriate waste disposal service.

J12

Troubleshooting

THE APPLIANCE DOES NOT WASH WELL

1. Check if the suction filter is dirty and clean it thoroughly.

2. Check if the wash jets are clogged and clean them.

3. Check that the initial amount of detergent or subse-

quent additions are correct.

4. The selected wash cycle is too short. Repeat the cycle.

5. Check that the tank temperature is at least 55°C /

131°F.

6. Check that the items are stacked correctly in the racks.

EXCESSIVE FOAM IN THE TANK

1. Check that the wash water temperature is not less than

55°C / 131°F.

2. Check if the amount of product dispensed by the deter-

gent dispenser is excessive (see "setting the dispen-

sers" paragraph).

3. Ensure that the tank has not been cleaned with unsui-

table cleaners. Drain the tank and rinse thoroughly

before new wash cycles.

4. If a foaming detergent has been used, drain and refill

the tank with water until the foam disappears.

THE WASH OR RINSE ARMS TURN SLOWLY

1. Remove and thoroughly clean the arms.

2. Clean the wash pump suction filter.