ページを印刷する
en Cleaning aid
11 Cleaning aid
The cleaning aid is a fast alternative for occasionally
cleaning the cooking compartment. The cleaning aid
evaporates soapy water and therefore softens dirt. This
means that dirt can be removed more easily.
11.1 Setting the cleaning aid
WARNING ‒ Risk of scalding!
If there is water in the cooking compartment when it is
hot, this may create hot steam.
Never pour water into the cooking compartment
▶
when the cooking compartment is hot.
Requirement: The cooking compartment must be
cooled down completely.
Remove the accessories from the cooking compart-
1.
ment.
Add one drop of detergent to 0.4 l water and pour it
2.
onto the centre of the cooking compartment floor.
Do not use distilled water.
Use the function selector to set the Bottom
3.
heating type of heating.
Use the temperature selector to set 80 °C.
4.
Press repeatedly until
5.
play.
Use
or
to set the duration to four minutes.
6.
a After a few seconds, the appliance starts heating
and the duration counts down.
a When the cooking time has counted down, a signal
sounds and the duration is at zero in the display.
12 EcoClean
Use the EcoClean cleaning function regularly to help
retain the cleaning ability of the self-cleaning surfaces
and prevent damage.
The self-cleaning surfaces in the cooking compartment
are coated with a porous, matte ceramic layer and
have a coarse surface. When the appliance is in opera-
tion, the self-cleaning surfaces absorb splashes of fat
from baking, roasting or grilling and break them down.
The following surfaces are self-cleaning:
¡ Back panel
¡ Door
¡ Side walls
ATTENTION!
If the self-cleaning surfaces are not cleaned regularly,
the surfaces may be damaged.
If dark spots can be seen on the self-cleaning sur-
▶
faces, use the cleaning function to clean the cook-
ing compartment.
If a request to clean appears, use the cleaning func-
▶
tion to clean the cooking compartment.
Do no use any oven cleaners or abrasive cleaning
▶
aids. If oven cleaner accidentally comes into contact
with the self-cleaning surfaces, dab the surfaces im-
mediately with water and a sponge cloth. Do not rub
them.
14
is selected in the dis-
Switch off the appliance and leave it to cool for ap-
7.
prox. 20 minutes.
11.2 Cleaning the cooking compartment
after using it
ATTENTION!
If the cooking compartment remains damp for too long,
this results in corrosion.
After using the cleaning aid, wipe the cooking com-
▶
partment and allow it to dry completely.
Requirement: The cooking compartment has cooled
down.
Open the appliance door and absorb the residual
1.
water with an absorbent sponge cloth.
Clean smooth surfaces in the cooking compartment
2.
with a dish cloth or a soft brush. Remove stubborn
residues with a stainless steel spiral scourer.
Remove limescale deposits using a vinegar-soaked
3.
cloth. Wipe this away with clear water and use a soft
cloth to also rub underneath the door seal dry.
Once the cooking compartment is sufficiently clean:
4.
In order to cool the cooking compartment, leave
‒
the appliance door open in the detent position
for approx. one hour.
To dry the cooking compartment more quickly,
‒
heat up the appliance with the door open with 3D
hot air and 50 °C for approx. five minutes.
12.1 Cleaning recommendation
The appliance records the type and duration of the op-
eration and, if required, recommends which cleaning
function to use.
When lights up in the display while the appliance
▶
is switched off, use the cleaning function as soon as
possible.
To remove the note from the display, press any
‒
button except for the
ues to appear until the cleaning function has
been carried out in its entirety.
To reset the cleaning recommendation, press
‒
and hold the
button for approx. four seconds.
The note no longer appears until the appliance
has recorded the corresponding number of oper-
ations again.
Notes
¡ If the appliance is prematurely contaminated, e.g. by
greasy poultry or roasts, or if dark spots appear on
the self-cleaning surfaces, do not wait until the note
appears in the display before you use the cleaning
functions. The more often the cleaning function is
used, the longer the cleaning ability of the self-
cleaning surfaces is retained.
¡ After a power failure, the cleaning recommendation
is reset. After a power failure, it is best to start the
cleaning function.
button. The note contin-