配管製品 Advanced Global Technology 525972のPDF インストール手順をオンラインで閲覧またはダウンロードできます。Advanced Global Technology 525972 2 ページ。 Single handle lavatory faucet

ページを印刷する

SINGLE HANDLE

LAVATORY FAUCET

Models 528224, 527747, 528109

529081, 529115, 529214, 527440

525998, 525980, 525972

Your new Design House faucet will give you years of trouble free performance. Thank you for

choosing our product for your home. Please read all of these instructions carefully before

installing your new faucet.

Helpful tools to install this faucet:

basin wrench

Teflon tape

(2) crescent wrenches

IMPORTANT POINTS

When installing your new faucet, hand tighten the connector nuts, then use one wrench to

anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that are

too tight will reduce the integrity of the system.

Wrap all threaded connections (except aerator thread in spout) with Teflon tape available from

your local hardware or plumbing supply store. Always wrap in a counter-clockwise direction.

ALWAYS protect your eyes with safety glasses.

TROUBLE SHOOTING

Problem: Faucet leaks from under handle.

Cause: Adjusting ring or cap nut is loose.

Action:

1. Remove handle by loosening set screw with

allen wrench.

2. Tighten the adjusting ring by turning it

clockwise with a small screwdriver. Move ball

stem to the on position and continually tighten

the adjusting ring until the leak stops draining

out from around the ball stem.

3. If the leak does not stop, loosen the adjusting

ring and tighten the entire cap assembly by

turning it clockwise. Retighten the adjusting ring

as before.

4. Replace the handle and tighten the set screw.

Many of these parts come preassembled.

This exploded diagram is to assist in

trouble shooting.

HANDLE

ADJUSTING RING

CAP NUT

SET

SCREW

HOT/COLD

INDICATOR

CAM ASSEMBLY

COVER

BALL ASSEMBLY

SEAT

SPRING

SPOUT

FAUCET

BODY

AERATOR

NOSE

RISER (2)

COUPLING

NUT (2)

silicon sealer

flashlight

faucet supply tubes

SAFETY TIPS

Problem: Water does not completely shut off.

Cause: Rubber valve seat is dirty or worn or

adjusting ring or cap has loosened.

Action:

1. Turn off the water under the sink.

2. Remove handle by removing hot/cold indicator

and loosening set screw with allen wrench.

3. Unscrew the cap nut. Remove the cam

assembly and ball assembly.

4. Inspect the two rubber valve seats for debris or

damage. Replace if necessary.

5. Push the rubber seats and springs back in with

smaller ends up. Take care when replacing the

metal ball to align the metal peg on the side of the

body with the oblong slot on the ball.

6. Reassemble the faucet taking care to fit the

small alignment tab on the cam into the slot. Make

sure cap nut is tight and fits flush with faucet body

before reattaching handle.

7. Retighten the adjusting ring. Replace the handle

and tighten the set screw.

8. Turn on the water under the sink.

Problem: Faucet leaks around aerator or has an

improper flow pattern.

Cause: Aerator incorrectly fitted or dirty.

Action:

1. Unscrew the aerator. Make sure all internal

parts are laying flat.

2. If there is debris, gently flush all parts inside.

3. Reinstall aerator.

POP-UP INSTALLATION

EXPLODED PARTS

LIFT ROD

DRAIN STOPPER

FLANGE

MACK WASHER

PLASTIC FRICTION

WASHER

LOCKNUT

THREADED

ROD

POP-UP DRAIN

BODY

COPPER

WATER INLET

GASKET

BUSHING

PIVOT ROD

& BALL

BUSHING

WASHER

PIVOT ROD

OPENING

TAIL PIECE

LOCK NUT

1. Shut off hot and cold water supplies under sink. Plug sink drain with cloth to avoid losing small

parts. Remove old faucet.

2. Screw both threaded rods into

the threaded receptacles located

under faucet body.

3. FIT GASKET TO BOTTOM OF

FAUCET BODY BEFORE

INSTALLING FAUCET ON SINK.

Install faucet with gasket through

sink holes. From under the sink

slide metal washers onto threaded

rods with the open slots around the

copper water inlets. Then screw

the locknuts onto the threaded rods.

Make sure faucet is in the correct

position and tighten locknuts.

Your new Design House faucet is designed to give you years of trouble free performance. Keep it

looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh

chemicals that will dull the finish and void your warranty.

Brass finishes are polished, then protected with a lacquer coating to help prevent tarnishing. Clean

these surfaces only with a damp, soft cloth.

Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the

amount of lead used in brass and solder. Your new faucet is made in strict compliance with all

government standards. The materials used in the manufacture of this faucet are of industry

standard quality and are similar to other plumbing products having brass fittings.

To reduce the amount of lead in your drinking water, allow the water to run for a moment before

filling your glass and remember to always use cold water for drinking purposes.

POP-UP (OPTIONAL) INSTALLATION PROCEDURE

1. Remove stopper and unscrew

flange from pop-up assembly.

2. Insert pop-up drain body with mack

washer, plastic friction washer (not

included with plastic pop-ups) and

locknut through bottom of sink drain.

3. Apply silicone sealer to the

underside of the flange and screw it

to the top of the the pop-up drain

body. Unscrew the tail piece. Add

Teflon tape to the tail piece threads

and reattach.

7. Insert pivot rod into the first spring

THUMB

SCREW

clip hole. Guide the pivot rod through

one of the holes in the rod strap and

secure in the second spring clip hole.

ROD

STRAP

8. Adjust the height of the lift rod by

loosening the thumb screw, positioning

the lift rod, and tightly resetting the

thumb screw.

SPRING

CLIP

RETAINING

NUT

INSTALLATION PROCEDURE

4. WRAP THREADED

SECTION OF THE COPPER

LINES WITH TEFLON TAPE

BEFORE CONNECTING

WATER SUPPLY LINES.

Connect copper water inlet to

hot and cold water lines using

coupling nuts and nose risers

if necessary. Use care to not

bend or kink the copper water

inlets. Bent or kinked inlets will

void the warranty.

2,3

MAINTENANCE

CONSUMER PROTECTION WARNING

4. Tighten locknut, making sure the

NON-

mack washer fits into drain hole. Insert

REMOVABLE

tail piece into waste drain tube and

tighten slipnut.

REMOVABLE

5. Insert stopper into the drain opening

in a removable or non-removable

position. Place pivot bushing inside of

pivot rod opening. Place pivot rod and

ball, and second bushing into opening.

Secure with retaining nut. Do not over

tighten.

6. Insert lift rod through lift rod strap.

Tighten with thumb screw.

5. Remove aerator and turn on

water. Allow both hot and cold

water to run for at least one

minute to flush system of any

debris. Turn off and replace

aerator.

6. Check for leaks. Correct by

slightly tightening connections. IF

LEAKS PERSIST, SEE TROUBLE

SHOOTING.

SILICONE

SEALER

TEFLON

TAPE

7,8