- ページ 6
温度コントローラー Drayton Lifestyle LP711SiのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Drayton Lifestyle LP711Si 20 ページ。 Central heating control
Drayton Lifestyle LP711Si にも： インストレーション・インストラクション (2 ページ), サービス手順 (2 ページ)
ページを印刷する
I
When you press SET? after setting OFF3, the timeswitch will
return to normal operation.
return to normal operation.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH
LP711Si – a 7-day program, allowing for different
LP711Si – a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods
timings on each day of the week, up to 3 heating periods
each day.
each day.
Want to leave a timing as it is? Just press SET? and move on
Want to leave a timing as it is? Just press SET? and move on
to the next one.
to the next one.
If you need to reset your timings to the standard program and
If you need to reset your timings to the standard program and
start again, press 'SET' and '+' together to go back to the
start again, press 'SET' and '+' together to go back to the
pre-set program.
pre-set program.
The standard program
The standard program
Your system will come on for up to 3 heating periods every
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
Notice that ON2 and OFF2 are set to the same time.* This
means your system won't respond, but if you want to activate
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
means your system won't respond, but if you want to activate
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
that middle period or change any other timings – read on.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
that middle period or change any other timings – read on.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
SWITCHING
SWITCHING
SWITCHING
SWITCHING
– start of first timed period
SWITCHING
ON 1
– start of first timed period
ON 1
– start of first timed period
ON 1
– start of first timed period
– end of first timed period
ON 1
OFF 1
– end of first timed period
– start of first timed period
OFF 1
– end of first timed period
ON 1
OFF 1
– end of first timed period
– start of second timed period*
OFF 1
ON 2
– start of second timed period*
– end of first timed period
ON 2
– start of second timed period*
OFF 1
ON 2
– start of second timed period*
– end of second timed period*
ON 2
OFF 2
– end of second timed period*
OFF 2
– start of second timed period*
– end of second timed period*
ON 2
OFF 2
– end of second timed period*
– start of third timed period
OFF 2
ON 3
– start of third timed period
ON 3
– end of second timed period*
– start of third timed period
OFF 2
ON 3
– start of third timed period
– final switch-off of the day
OFF 3
ON 3
– final switch-off of the day
OFF 3
– final switch-off of the day
– start of third timed period
OFF 3
ON 3
– final switch-off of the day
OFF 3
– final switch-off of the day
OFF 3
Changing the timings
Changing the timings
I
Changing the timings
I
Press the SET? button and you'll see 'SET PROG?'.
Changing the timings
I
Press the SET? button and you'll see 'SET PROG?'.
I
Press the SET? button and you'll see 'SET PROG?'.
Changing the timings
Press the SET? button and you'll see 'SET PROG?'.
I
Press the SET? button and you'll see 'SET PROG?'.
PROG?
Set all weekdays
Set all weekdays
Set all weekdays
Set all weekdays
First you set the times that are going to be the same for each
First you set the times that are going to be the same for each
Set all weekdays
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
any further adjustments. If you want each day to be quite
different, go straight to 'Set each day'.
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
different, go straight to 'Set each day'.
different, go straight to 'Set each day'.
any further adjustments. If you want each day to be quite
I
different, go straight to 'Set each day'.
I
Press the YES button, and the display will ask 'SET MON to FRI
I
different, go straight to 'Set each day'.
Press the YES button, and the display will ask 'SET MON to FRI
I
Press the YES button, and the display will ask 'SET MON to FRI
PROG?'.
Press the YES button, and the display will ask 'SET MON to FRI
PROG?'.
I
PROG?'.
Press the YES button, and the display will ask 'SET MON to FRI
PROG?'.
PROG?'.
MON TUE WED THU FRI
PROG?
I
I
Press YES and you'll see ON1, the start of your first heating peri-
I
Press YES and you'll see ON1, the start of your first heating peri-
I
Press YES and you'll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
Press YES and you'll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
I
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
Press YES and you'll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
If the – and + buttons are held down, the time changes in
10-minute steps.
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
10-minute steps.
10-minute steps.
If the – and + buttons are held down, the time changes in
10-minute steps.
10-minute steps.
STANDARD PROGRAM
STANDARD PROGRAM
STANDARD PROGRAM
STANDARD PROGRAM
MON-FRI
SAT-SUN
MON-FRI
SAT-SUN
STANDARD PROGRAM
MON-FRI
SAT-SUN
6.30am
7.00am
MON-FRI
SAT-SUN
6.30am
7.00am
6.30am
7.00am
MON-FRI
SAT-SUN
6.30am
7.00am
8.30am
9.00am
8.30am
9.00am
6.30am
7.00am
8.30am
9.00am
8.30am
9.00am
12.00pm
12.00pm
12.00pm
12.00pm
8.30am
9.00am
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
12.00pm
4.30pm
4.00pm
4.30pm
4.00pm
12.00pm
12.00pm
4.30pm
4.00pm
10.30pm
4.30pm
11.00pm
4.00pm
10.30pm
11.00pm
10.30pm
4.30pm
11.00pm
4.00pm
10.30pm
11.00pm
10.30pm
11.00pm
User's In
PROGR
PROGR
If the engineer has set your
If the engineer has set you
won't need to do anything e
won't need to do anything
safe place for future referen
safe place for future refere
INTRODUCTION
INTRODUCTION
Lifestyle Programmers will a
Lifestyle Programmers will
heating and hot water on an
heating and hot water on a
Depending on your system
Depending on your system
can either both come on an
can either both come on a
independently. The red ligh
independently. The red ligh
shows when each one is o
shows when each one is o
INTRODUCTION Cont...
INTRODUCTION Cont...
INTRODUCTION Cont...
INTRODUCTION Cont...
There are 3 models in the Life
There are 3 models in the Life
INTRODUCTION Cont...
I
There are 3 models in the Life
I
There are 3 models in the Lif
LP241Si – a 24hr program,
I
LP241Si – a 24hr program,
I
There are 3 models in the Li
LP241Si – a 24hr program,
working independently for
LP241Si – a 24hr program
working independently for u
I
working independently for
every day the same.
LP241Si – a 24hr program
working independently for
every day the same.
I
every day the same.
working independently fo
I
every day the same.
LP522Si – a 5/2-day progra
I
LP522Si – a 5/2-day program
I
every day the same.
LP522Si – a 5/2-day progra
the weekends, with central
LP522Si – a 5/2-day progr
the weekends, with central h
I
the weekends, with central
independently for up to 3 h
LP522Si – a 5/2-day prog
the weekends, with centra
independently for up to 3 he
I
independently for up to 3 h
the weekends, with centra
I
independently for up to 3 h
LP722Si – a 7-day program
I
LP722Si – a 7-day program
I
independently for up to 3
LP722Si – a 7-day program
each day of the week, with
LP722Si – a 7-day program
each day of the week, with
I
each day of the week, with
working independently for
LP722Si – a 7-day progra
each day of the week, with
working independently for u
working independently for
each day of the week, wit
working independently for
working independently fo
If the engineer hasn't set y
If the engineer hasn't set yo
If the engineer hasn't set y
will work with a standard p
If the engineer hasn't set y
will work with a standard pr
will work with a standard p
factory. If this doesn't suit y
If the engineer hasn't set
will work with a standard p
factory. If this doesn't suit yo
factory. If this doesn't suit y
when you've read this intro
will work with a standard
factory. If this doesn't suit
when you've read this introd
when you've read this intro
section that contains your
factory. If this doesn't suit
when you've read this intro
section that contains your p
section that contains your
when you've read this intr
section that contains your
section that contains your
Remember:
Remember:
I
Remember:
I
Remember:
Make your changes using
I
Make your changes using th
I
Remember:
Make your changes using
the programmer.
Make your changes using
the programmer.
I
I
the programmer.
Make your changes using
I
the programmer.
You can't set ON1 as the la
I
You can't set ON1 as the la
I
the programmer.
You can't set ON1 as the la
can set OFF3 after midnigh
You can't set ON1 as the l
can set OFF3 after midnigh
I
can set OFF3 after midnigh
hours and 59 minutes after
You can't set ON1 as the
can set OFF3 after midnig
hours and 59 minutes after
I
hours and 59 minutes after
can set OFF3 after midnig
I
hours and 59 minutes afte
You need to set the timings
I
You need to set the timings
I
hours and 59 minutes afte
You need to set the timings
OFF2, ON3, OFF3. If you g
You need to set the timing
OFF2, ON3, OFF3. If you g
I
OFF2, ON3, OFF3. If you g
flash a warning.
You need to set the timing
OFF2, ON3, OFF3. If you
flash a warning.
flash a warning.
OFF2, ON3, OFF3. If you
flash a warning.
flash a warning.
SWITCHING
SWITCHING
SWITCHING
– start o
SWITCHING
ON 1
– start of
ON 1
– start o
SWITCHING
ON 1
– start
ON 1
– end
OFF 1
– end o
OFF 1
ON 1
– end
OFF 1
OFF 1
– start o
ON 2
– start of
ON 2
– start
– end