- ページ 4
スピーカー Anchor Explorer ProのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Anchor Explorer Pro 4 ページ。 Anchor audio portable sound system
Anchor Explorer Pro にも： オーナーズマニュアル (8 ページ), ユーザーマニュアル (13 ページ), オーナーズマニュアル (8 ページ)
ページを印刷する
BASIC SYSTEM OPERATION
NOTE: Fully Charge Battery Before First DC Use!
1. Set all Input Level Controls to minimum & Tones Controls to flat
or the middle setting before turning your system on
2. Plug a wired microphone into the MIC 1 or MIC 2 jacks and/or
plug an audio source into the LINE-IN jack
3. Switch POWER to ON, the BATTERY LED will light
4. Slowly increase the Level Control for the input jacks used
to the desired volume
5. Adjust BASS & TREBLE controls to desired sound quality
IMPORTANT: Make all connections w/ shielded
cables to avoid hum, buzzing or interference.
CARING FOR YOUR BUILT-IN BATTERY
An automatic charging system is built-in to your Explorer PRO Sound System.
It is designed to properly charge and maintain the systems built-in battery.
CHARGING THE BATTERY
1. Plug the AC power cord into the Explorer PRO
2. Plug the other end of the cord into AC outlet
3. The Charge Indicator Light will turn green when
battery is fully charged
To preserve the life of your battery it is recommended that it be fully charged as
soon as possible after every use regardless of the length of operation.
NOTE: System Can Be Used While Battery Charges!
OPERATING IN AC MODE
Plug your sound system into an AC outlet. Operate the system normally while
the built-in battery charges automatically. The Charge Indicator Light will
glow a solid yellow while charging and turn green when the battery is fully
charged.
IMPORTANT: Always Store Your System w/
Battery Fully Charged!
STEREO LINE INPUT JACK
A 1/8" (3.5 mm) jack located on the back of
the Explorer PRO above the control panel.
This stereo line input is used for playback
of a CD/MP3/tape player, laptop computer
or similar external audio source.
STEREO LINE
INPUT JACK
4
WIRELESS RECEIVER 1
(see page 6)
LINE IN LEVEL CONTROL
MICROPHONE LEVEL CONTROLS
Pull knob out to control wireless
microphone levels
Push knob in to control levels
on wired microphones connected
to the Universal Mic Input Jacks
UNIVERSAL MIC - INPUT JACKS
Balanced XLR - balanced low imped-
ance mics, powers condenser mics
Unbalanced 1/4" - unbalanced high
impedance mics, no phantom power
SPEAKER OUT - OUTPUT JACK
Balanced 1/4" - use speaker output
to drive an unpowered 2 ohm
speaker in addition to Explorers
built-in speakers for greater output
POWER SWITCH
EXPLORER PRO SOUND SYSTEM
CONTROL PANEL
Model Shown: EXP-6000U2
BATTERY LEVEL INDICATOR LIGHT
The Explorer PRO sound system features a built in Battery Level Indicator Light that
shows the battery level in three steps at power on.
1. GREEN: Battery is fully charged
3. RED: Battery level becoming low
(system auto-shutoff in 15-30 minutes)
2. YELLOW: Battery level is depleted
NEED MORE HELP? Visit Our Website: www.anchoraudio.com
VOICE OVER BUTTON
When pressed (button in) reduces the Line Input &
CD Input levels by 12 dB when any microphone is used
VOICE OVER allows speaker to be heard over background music
BATTERY LEVEL INDICATOR LIGHT
The system is equipped with a built in rapid charger, designed to quickly charge and
maintain the battery. If the Charge Indicator Light is:
YELLOW (flashing): Battery being tested
(about 30 seconds when AC is connected)
YELLOW (solid): Battery is in good
condition, rapid charging has begun
WIRELESS RECEIVER 2
(see page 6)
TONE CONTROLS - BASS/TREBLE
1/4" PHONE & DUAL RCA
LINE IN - INPUT JACKS
Jacks may be used simultaneously and
can be combined w/ the mic inputs for
a composite output - For playback of
tape/CD player or other audio source
RECORD OUT
Composite output signal of all inputs
Use to record your presentation
LINE OUT - OUTPUT JACK
Balanced 1/4" - provides a combined
output of all active system inputs
Record your presentation or connect
to another powered sound system
12V DC INPUT JACK
CHARGE INDICATOR LIGHT
AC POWER CORD INLET
CHARGE INDICATOR LIGHT
GREEN: Battery is fully charged
RED: Indicates battery fault, please
call the Anchor Audio customer service
department: (888) 444-6077