- ページ 8

電動工具 Bosch 1529BのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch 1529B 33 ページ。 Nibbler
Bosch 1529B にも：取扱説明書 (25 ページ)

ページを印刷する

BM 1609929Y02 05-10:BM 1609929Y02 05-10 5/10/10 9:16 AM Page 8

CHANGING PUNCHES AND DIES

Disconnect the plug from

W RNING

the power source before

making any assembly, adjustments or

changing accessories. Such preventive

safety measures reduce the risk of starting

the tool accidentally.

REPLACING THE PUNCH

Loosen the winged screw and pull the die

holder (including the die and knurled nut) out

of the housing. Slide the punch sideways out

of the groove and remove downward.

Oil the new punch well, insert into the groove

and center.

Slide the die holder carefully over the punch

and into the housing. Re-tighten the winged

GENERAL INFORMATION

Following a few simple tips will reduce wear on

the tool and the chance of injury to the user.

With the tool unplugged from the power supply

and the ON/OFF Switch in the "OFF" position,

become familiar with handling the nibbler and

learning the location of its parts.

Before running the nibbler, inspect the punch

and die for excessive wear, and replace if

necessary.

Do not exceed recommended capacities for

this nibbler. Premature punch and die failure

will occur when the nibbler is under- or over-

gaged.

Never start the nibbler with the punch and die

in contact with the material being cut.

For clean and fast cuts, hold the nibbler so that

the cutting head is at a right angle to the

cutting path, with the body of the tool parallel to

the corrugations. Move the cutting head in and

out of the corrugations, constantly keeping the

head at a right angle to the material being cut.

Feed the nibbler into the work with a minimum

of pressure. Let the nibbler do the work. If the

nibbler doesn't cut correctly, check for a dull

punch or die. Dulling will be apparent as more

pressure is required to feed the nibbler into the

material. Burrs will also show along the cut

edge. A harder material will dull the punch and

die faster than a soft material.

Assembly

screw. The winged screw must engage one of

the holes in the die holder.

NOTE: The punch cannot be reground.

Unscrew the knurled nut together with the

rubber ring out of the die holder and remove

the die. Remove any rust material or cutting

particles that may have collected in the die

holder.

Insert a new die paying attention to the

alignment of the flat surface on the side. Firmly

tighten the knurled nut against the resistance

of the rubber ring.

NOTE: The die cannot be reground.

Operating Instructions

Always direct the cord toward the rear, and

away from the nibbler. Keep it away from

sharp edges.

Secure or clamp small workpieces to be cut to

prevent slippage.

Always use recommended lubricant for the

material being cut. Lack of lubricant will

shorten punch and die life.

The Paddle Switch enables the operator to

control the switch functions of "ON/OFF" and

"Lock-ON".

TO SWITCH TOOL "ON": Squeeze and hold

the paddle lever.

TO SWITCH TOOL "OFF": Release pressure

on the paddle lever. The switch is spring

loaded and will return to "OFF" position

automatically.

The "Lock-ON" feature, incorporated into the

paddle switch, is a convenience for long

operations.

TO LOCK SWITCH "ON": After switch has

been activated, PULL the front portion of the

paddle lever completely BACKWARD and

release pressure on the paddle lever.

TO SWITCH TOOL "OFF": Squeeze the rear

portion of paddle lever and then release the

paddle lever. The switch is spring loaded and

will return to "OFF" position automatically.

-8-

REPLACING THE DIE

PADDLE SWITCH WITH

"LOCK-ON" FEATURE