- ページ 8

電動工具 Bosch 1944LCDK - Programmable Electronic Heat GunのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch 1944LCDK - Programmable Electronic Heat Gun 33 ページ。 Robert bosch tool corporation user guide impact driver lcd

ページを印刷する

BM 1619929572 08-07

SETTING THE AIR FLOW

The air flow can be regulated with the air flow

button (Fig. 1).

Minimum air flow (approx. 3.6-8.8 CFM,

depending on temperature setting)

Maximum air flow (approx. 17.6 CFM)

The CFM at each of the 10 airflow settings

depends on the temperature setting. For

example, at the lowest temperature (120

degrees) the lowest airflow setting delivers 3.6

cfm, whereas at the highest temperature (1200

degrees) the lowest airflow setting delivers 8.8 cfm

The air flow can be increased by pressing the

"+" side of the air flow button or decreased by

pushing the "–" side of the button. Brief

pressing of the button increases or decreases

the air flow by one step. Longer pressing of the

button increases or decreases the air flow

continuously until the maximum or minimum air

flow is reached.

Decrease the air flow when, for example:

The surroundings of the workpiece should not

be heated more than necessary. A light

workpiece could be blown away by the air

stream.

PROGRAMMED OPERATION

In programmed operation, air flow and

temperature settings can be stored in four

programs. In each program, any air flow and

temperature combination are possible.

Also in programmed operation, air flow and

temperature can be changed at any time. If the

changes

are

reprogramming, they are lost when switching

the unit off or when changing to another

program.

To use one of the pre-stored modes, press the

program selection button "P" until the number

of the required program (

shown in the display (Fig. 2).

PRE-STORED PROGRAMS

The unit is equipped with the following four pre-

stored programs:

Program Application

Shaping of plastic

tubing (e.g. LDPE)

Welding of plastic

(e.g. PVC)

Removing paint/

softening adhesives

Soldering

8/28/07

9:45 AM

not

stored

through

) as

Temperature Air

Flow

480 °F

660 °F

860 °F

1000 °F

Page 8

REPROGRAMMING

Press the program selection button "P" until

the

number

reprogrammed is shown in the display. Set the

required temperature and air flow (see figure 3).

As soon as the values of the program are

altered, the symbol blinks

the display.

After setting the required air flow and

temperature, press the store button

5 seconds) until the symbol

disappears. The values set are now stored

under the program number shown in the

display.

NORMAL OPERATION

To change to normal operation, press the

program selection button "P" repeatedly until

there is no longer a program number shown

over the temperature in the display.

The air flow and temperature can be changed

at any time.

The last set unprogramed values for the air flow

and temperature remain stored under the

following conditions:

– Move to program operation

– Move to the cool setting

– Switch-off the unit

REMOVING THE HEAT PROTECTOR

For working in especially narrow places, the

heat protector can be removed.

Be careful of the hot nozzle!

WARNING

Increased danger of burning

exists when working without the heat protector.

To remove or mount the heat protector, the unit

must be turned off and have cooled. To cool

unit down, run unit briefly in the cool air setting,

if necessary.

Turn the heat protector counter-clockwise to

remove, and clockwise to mount again.

USING THE UNIT IN

STATIONARY POSITION

For cooling of the heated unit or to have both

hands free for working, the unit can be set

down in the upright position on the stand legs

on the rear of the tool (Fig. 6).

Be especially careful when

WARNING

working with the upright unit!

There is danger of burning by the hot nozzle

and the hot air stream.

-8-

the

program

in the upper left of

(for about

in the display