- ページ 7

テント Anchor Navi-Trac LT/CSのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Anchor Navi-Trac LT/CS 16 ページ。 Pavilion 12' to 24' projection

ページを印刷する

Step 1 - Parts Layout

•

Follow the directions on the previ-

ous page for squaring and marking

for the frame.

•

Lay out the parts neatly in their ap-

proximate location, as if the frame

were collapsed onto the ground.

(Figure 1a)

•

Step 2 - Beam Arch As-

sembly

•

Assemble the ﬁ rst beam arch in the

following order:

1. Assemble upper triangle ﬁ rst

by fastening upright rear upper

splice to ridge weldment using

one of the pins attached to the

ridge weldment.

2. Drop hook end of Eave Projec-

tion into Eave End Weldment

Bracket. (Figure 2a) Note: On

24' projection, Eave projection

is spliced. Slide Eave Splice

Projection into 24' Eave Projec-

tion and fasten using 1/2" bolt

and nut.

3. Drop slotted end of Eave

Projection down over ear

located at bottom of upright

rear upper splice and pin

using a tension lock pin.

(Figure 2b)

4. Assemble Rafter Splice

Projection to Rafter using

1/2" bolt and nut provided

(required only on frames

over 20' projection)

5. Slide Rafter up onto ridge

weldment and afﬁ x using method detailed as follows:

•

On rafters with "X" cables in one of the adjacent bays such as end

bays (see illustration on page 5) connection must be made using the

eye nuts and bolts shipped with the "X" cables. Eye nut must face in

the direction of the "X" cabled bay because it is used for connection of

the "X" cables. (See Step 3)

•

In the case where there are two "X" cabled bay adjacent to one

another, the connection must be made using an eye bolt with eye nut.

(not usual)

•

On rafters with no "X" cables attach the rafter using the pin attached to

the ridge weldment.

On frames with 20' projection or more, rafter brace is now attached to triangle.

Rafter Brace will only ﬁ t one way- so if you are having trouble with alignment,

turn the brace around so that the opposite ends are now at the rafter and up-

right rear upper splice. (See Figure 2c)

Assemble uprights by sliding adjustable base plates into uprights and bolting

with bolts provided. See Figure 2d for assistance in assembling the upright in

the correct position.

On Rear upright, slide Upright rear upper splice down into bottom upright and

pin with a tension lock pin. See Figure 2d for assistance in assembling the

upright in the correct position.

Assemble all Beam arches with baseplates in correct position for raising.

Ridge

Weldment

Upright

Rear

Upper

Splice

Upright

Upright (only on

frames over 20'

projection.)

Base Plate

Adjustable

4-Hole

Eave End Weldment

Eave projection

Rafter Splice

Projection

Rafter Brace (only

on frames 20' pro-

jection and larger.

End Upright

Eave Weld-

ment

Base Plate

Adjustable

2-Hole

Note: End Upright used only on

frames larger that 20' projection.

Figure 2a

Channeled

side of upright.

toward inside

of frame.

22' Projection Frame Shown

Rafter

Eave End

Weldment

Eave Projection

Upright

Base Plate

Adjustable

4-Hole

Slot

Eave projection

Upright Rear Upper

Splice Ear

Upright Rear

Upper Splice

Tension

Lock Pin

Cross-sectional view of

Navi-Trac Lite Beam

Flat side of

upright. toward

outside of frame.

Figure 1

Figure 2b

Rafter

Figure 2c

Figure 2d