ウインチ Andersen WINCH 16のPDF 取付方法をオンラインで閲覧またはダウンロードできます。Andersen WINCH 16 2 ページ。

ページを印刷する

MOUNTING INSTRUCTION

WINCH 16,

Remove circlip (1), using a small sharp screw driver.

Remove drum (2).

Mark location of the bolt holes using the winch base (12) as a tem-

plate.

Remove the winch base. Be sure that no dust comes into contact with

the winch while drilling the bolt holes.

Drill the bolt holes ø6.5mm.

Clean the area.

Apply a light coat of bedding compound, ensuring that each hole is

bedded. Drain grooves should be kept clear.

Fasten the winch into place using 5 pcs. countersunk head screws.

Reassemble in reverse order.

10. Check that the winch is functioning correctly.

SERVICE INSTRUCTION

WINCH 16,

Maintenance interval 1-2 years, depending on operation conditions.

Remove circlip (1).

Remove drum (2).

Remove the black plastic circlip (10).

Remove the drive shaft (6).

Remove the roller bearings (9,11).

Remove gear shaft (13), using a standard screwdriver.

Remove gear wheel (14).

Clean all moving parts with benzine. Please note. Direct acces to the

ratchet gear (15) requires the winch base (12) to be removed from the

deck surface, in order to release the base bottom cap (16).

Check pawls & springs for wear and replace if necessary. In order to

replace the upper pawls (4) or springs (5), the gliding washer (3)

must be removed.

10. Reassemble the winch in reverse order, lightly greasing all moving

parts, with a soft, small brush. We strongly recommend to use only

ANDERSEN Winch Grease for this purpose*

11. Check that the winch is functioning correctly.

*) Most types of grease, including "marine grease" are NOT suitable for lubrication of

winches. None suitable grease can cause mechanical malfunction. Malfunctioning pawls may

lead to unexpected failure of a loaded winch, resulting in material damage or fatal personal

injury.

Service Kit No. 4 (part no. 710004) contains service parts for this winch.

PARTS LIST

WINCH 16,

POS

QTY

DESCRIPTION

CIRCLIP

DRUM

GLIDING WASHER

PAWL

PAWL SPRING

DRIVE SHAFT, COMPLETE

PAWL SPRING

PAWL

ROLLER BEARING

CIRCLIP

ROLLER BEARING

WINCH BASE

GEAR SHAFT

GEAR WHEEL

RATCHET GEAR

BASE BOTTOM CAP

www.Busse-Yachtshop.de - [email protected]

VER.1.1

PART NO.

712800

715200

718400

713200

713300

715500

713300

713200

712905

716001

712905

730100

715700

715400

711701

715800

LIMITED WARRANTY

1.1

ANDERSEN issues a three-year warranty on all their products covering manufacturing and

material defects on condition that the products are used in normal fashion. The warranty shall

apply for three years from the moment ANDERSEN sell the product concerned (to the first

buyer).

1.2

Within the period of the warranty, and in accordance with the terms of the warranty, ANDERSEN

undertake to replace or repair all defective components, which have been used in normal

fashion.

1.3

The warranty is however subject to the limitations and exceptions outlined below.

Conditions and limitations:

2.1

ANDERSEN´s liability shall be limited to repair or replacement of components, which are

defective owing to manufacturing or material defects.

2.2

ANDERSEN assume no other liability than this, not even liability for indirect losses caused by

defect concerned, including operating losses, loss of profits, or damage caused to real property

or moveable property occurring while the product concerned is in the possession of the Buyer.

2.3

The Buyer alone shall bear the responsibility and risk involved as to whether the products are

suitable for the application intended. ANDERSEN assume no liability in this connection.

2.4

ANDERSEN assume no liability for defects which occur due to use of their products for purposes

for which they are not intended, or for defects which occur owing to incorrect installation,

corrosion, ultraviolet degradation, lack of maintenance, or any alteration or repair of the product

carried out incorrectly by the Buyer. Finally, ANDERSEN assume no liability for normal wear and

tear, or for depreciation in value.

2.5

ANDERSEN do not assume any liability for service carried out by anyone other than authorised

ANDERSEN representatives, unless such service is carried out pursuant to guidelines laid down

by ANDERSEN and in accordance with good craftsmanship.

2.6

The buyer shall inform ANDERSEN in writing of any defects with no undue delay once defects

have been registered. Products being dealt with under the warranty shall be returned to ANDER-

SEN for repair unless any other agreement has been reached in writing.

2.7

ANDERSEN shall not cover costs incurred by the Buyer in connection with the transport or

wages involved in a warranty case. The Buyer in full shall meet such costs.

Exceptions:

3.1

The warranty is only valid for one year in respect of components bought for the products con-

cerned, such as electric motors, electric equipment, hydraulic pumps, motors and valves.

3.2

ANDERSEN assume no liability for consequential damage of ships, equipment, property or

people caused by defects in ANDERSEN products.

3.3

The company's products are subject to continuous development, and consequently ANDERSEN

reserve the right to change designs and specifications without prior notice.

EXPLODED VIEW

WINCH 16,

VER.1.1