- ページ 16

冷凍庫 Electrolux AOFP101U4のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Electrolux AOFP101U4 27 ページ。 Bcf 30kg 6 gn1/1 lw (240/3/60hz), bcf 50kg 10 gn1/1 lw (240/3/60hz) / bcf 100kg 20 gn1/1 lw (240/3/60hz) / bcf 70kg 10 gn2/1 lw (240/3/60hz) / bcf 180kg 20 gn2/1 lw (240/3/60hz) / bcf 30kg 6 gn1/1 lw (208/3/60hz) / bcf 50kg 10 gn1/1 lw (208/3/60hz) / bcf

ページを印刷する

program indicator light

• to start the program, press the

The user can edit some of the cycle parameters and save the

changes:

- for blast chilling, the user can edit the chamber chilling time/

setpoint and save it in the memory, from where it can

subsequently be retrieved (see section C.2.2.3 and C.2.2.4).

- for positive maintenance, the user can set the chamber

setpoint.

C.2.2.5 Modification of chilling time

Chilling time is modifiable in the following cases:

1) during setting of a programme (P1 or P2)

2) during the selection phase of a chilling cycle

3) during actual chilling (can only be decreased).

For modification, proceed as follows:

• press the key

• the display will flash to show that modification phase is active;

• set the desired value using the keys

• press the key

will take place automatically after five seconds of inactivity.

C.2.2.6 Modification of cell temperature

• Chilling cycles: the set point can be modified only during

selection of a custom cycle or during "turbo cooling".

• Holding cycles (all).

In all cases proceed as follows:

• press the key

• the display will flash to show that modification phase is active;

• set the desired value using the keys

• press the key

If a selection is not made after 5 seconds, the last value

displayed will be confirmed automatically.

switches on.

button.

for two seconds;

;

to confirm the value. Confirmation

for two seconds;

;

to confirm the value.

C.2.2.7 Displaying the temperature setpoint and chilling end

time

When a cycle is running, the user can view the temperature

setpoint and chilling end time by pressing buttons

and

C.2.2.8 Changing the Standard selection

To select a Standard, e.g. the Electrolux Food Safe Mode 2,

press the

button, press the

Standard utility is selected,

press the

button to enter, press the

the Standard

either press the

confirm the selection or it will be confirmed automatically if

nothing is pressed for 12 seconds.

C.2.2.9 Editing USER parameters

To edit a parameter, select the utility:

• press the

button;

• the display blinks to show that the parameter is in 'edit' mode;

• press the

setting range;

• press the button to confirm the settings; if a selection is not

made after 5 seconds, the last value displayed will be confirmed

automatically, or press

NOTE: the parameters can be edited ONLY if no cycle is running.

If a cycle is running, the utility will enable only the display of the

parameters.

See section D.6 for the "List of user parameters".

C.2.3 BLAST CHILLING/PRESERVATION CYCLE

When the chilling or freezing cycle has finished, the appliance

will automatically go into the preservation stage. It is important

for the chilled food to be kept in an appropriate way, maintaining

a preservation temperature suitable for the type of food chilled.

simultaneously.

button until the

button again to

buttons to change the value within the

again.

button to select