- ページ 29

ドライヤー Bosch 6 SeriesのPDF 据付・取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch 6 Series 36 ページ。 2 door top freezer, inox-easyclean
Bosch 6 Series にも：ユーザーマニュアル (24 ページ), 取付・使用説明書 (20 ページ), 取付・使用説明書 (20 ページ), 取付・使用説明書 (20 ページ), 取扱説明書および取付説明書 (48 ページ), 取扱説明書 (16 ページ), 取扱説明書 (48 ページ), 取付説明書 (27 ページ), 取扱説明書 (12 ページ), 取扱説明書 (16 ページ), 取付・使用説明書 (16 ページ), 取扱説明書 (29 ページ), ユーザーマニュアルと設置手順 (16 ページ), ご利用案内 (32 ページ), クイック・リファレンス・マニュアル (2 ページ), クイック・リファレンス・マニュアル (2 ページ), ご利用案内 (28 ページ), ユーザーマニュアル (23 ページ), 取扱説明書 (24 ページ), 取付説明書および使用説明書 (24 ページ), ご利用案内 (16 ページ), ユーザーマニュアル (36 ページ), ユーザーマニュアル (32 ページ), ユーザーマニュアル (28 ページ), ユーザーマニュアル (28 ページ), 取扱説明書 (28 ページ), ご利用案内 (20 ページ), 取扱説明書 (28 ページ)

ページを印刷する

Faults and what to do about them

F a u l t s a n d w h a t t o d o a b o u t t h e m

Faults

ð in the display panel

and drying has been

interrupted.

é in the display panel.

Dryer does not start.

Display panel goes off

and Start button flashes.

Creasing.

Water is leaking out.

Change in the pro-

gramme duration dis-

played during drying.

Laundry is not dried cor-

rectly or is still too damp.

Depending on the model

Cause/remedy

Empty the condensate container; ~ Page 25 and the dryer; ~ Page 13.

■

If the optional condensation drain is installed, the drain hose may be

■

blocked. Check the hose for deposits and flush the hose out.

Clean the fluff filter and/or the heat exchanger, then select the Start button

~ Page 24; ~ Page 27.

Mains plug plugged in or fuse checked?

■

Programme selected? Select a programme.

■

Dryer door open? Close the door.

■

Is the childproof lock activated? Deactivate the child-proof lock.

■

"Ready in" time selected? Programme starts after a delay.

■

Not a fault. Energy-saving mode is active ~ Page 11.

Creasing occurs when you have exceeded the maximum load or selected

■

the wrong programme for the type of fabric. All the required information

can be found in the programme table.

Remove clothes immediately after drying; creasing may occur if they are

■

left in the drum.

Not a fault; the dryer may be positioned on an incline. Level the dryer.

Not a fault. The moisture sensors detect the remaining moisture in the load and

adjust the programme length (except timed programmes).

After the end of the programme, warm laundry feels damper than it actually

■

is. Spread the laundry out and allow the heat to disperse.

Finely adjust the dryness level – this extends the drying time but does not

■

increase the temperature. Your laundry becomes drier ~ Page 21.

Select a programme with a longer drying time or increase the drying level.

■

This does not increase the temperature.

Select a time programme for subsequent drying of laundry that is still damp

■

~ Page 19.

If you have exceeded the maximum load for the programme, the laundry

■

may not be dried properly.

Clean the moisture sensor in the drum. The sensor may become covered by

■

a fine layer of limescale or residues of detergents and care products which

then impair its function. Your laundry is not being dried correctly

~ Page 28.

Drying has been interrupted as a result of a power cut, because

■

the condensate container is full or because the maximum drying time has

been exceeded.

Note: