Installation
Technical data
– Delivery specification: dryer, instructions for installation and use, woollens basket
(depending on model).
– Check dryer for transport damage.
– The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not lift the dryer by any of the protruding parts (e.g. the door) as they may break off.
– Do not set up in a room that is susceptible to frost.
Freezing water may cause damage.
– If in doubt, have the appliance connected by an expert.
Setting up the dryer
1.
Take all accessory parts
– The appliance plug must always be accessible.
out of the drum.
The drum must be empty.
– Ensure that the appliance is installed on a clean, level
and solid surface.
– Keep the cooling grille at the front of the dryer
unobstructed.
– Keep the area around the dryer clean.
– Make the dryer level using the threaded feet
and a spirit level.
Do not remove the threaded feet under any
circumstances.
Do not set up the dryer behind a door or sliding
door as this may obstruct or prevent the dryer door
from opening. This will prevent a potentially fatal
danger to children from locking themselves in.
Clean and level
Make sure that the air
inlet remains unobstructed
2.
Mains connection
see safety instructions
Page 11.
– Connect to an AC earthed socket. If in doubt have the socket checked by an expert.
– The mains voltage and the voltage shown on the rating plate (
Page 9) must correspond.
– The connected load and necessary fuse protection are specified on the rating plate.
Do not operate the dryer if
Frost protection / Transport
there is a danger of frost.
Preparation
1. Empty the condensation container
page 4.
Optional accessories
2. Select any programme using the programme selector.
3. Press the
Start/Stop button
condensation is pumped into the container.
4. Wait 5 min., and then empty the condensation container again.
WTZ
5. Turn the programme selector to Off.
1110
WTZ
11310
WTZ
10290
7
8
What to do if ...
Dimensions (DxWxH)
60 x 60 x 85 cm (height adjustable)
If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales
service. We will always find an appropriate solution and will avoid unnecessary visits by
Weight
approximately 45 kg
engineers. Trust the expertise of the manufacturer and rest assured that the repair will be
Max. capacity
8 kg
carried out by trained service technicians using original spare parts. The contact details of your
local after-sales service can be found in the enclosed after-sales service directory, or by
Condensation container
4.2 l
calling one of these numbers:
Connection voltage
– GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.
Connected load
A call set-up fee of up to 6 pence may apply.)
– IE 01450 2655
Fuse protection
see appliance rating plate
When contacting the after-sales service, please quote the appliance's product number (E no.)
Ambient temperature
and production number (FD) (see the inside of the door).
Product number/
Set the programme selector to Off and remove the appliance plug from the socket.
Production number
The
Start/Stop indicator lamp
does not light up.
You can find the rating plate on the back of the dryer.
The
Container
Consumption rates
These are guide values determined under standard
Start/Stop indicator lights are
conditions.
flashing.
Fluctuations up to 10% are possible.
The
Filter
and
Spin speed in rpm
Drying time
Energy
indicator lights are flashing.
(residual moisture)
in min.**
consumption
Dryer does not start.
in kWh**
Cottons 8 kg
13 A
13 A
Cupboard Dry*
1400 (approx. 50 %)
105
3.74
Water is running out.
1000 (approx. 60 %)
122
4.49
800
(approx. 70 %)
139
5.17
The door opens by itself.
Iron Dry*
1400 (approx. 50 %)
83
2.24
Creasing.
1000 (approx. 60 %)
100
3.44
800
(approx. 70 %)
117
3.86
Easy-Care 3.5 kg
1000
39
1.05
Drying result is not satisfactory
(laundry feels too damp).
Cupboard Dry*
800
(approx. 40 %)
42
1.35
600
(approx. 50 %)
51
1.65
*Test program according to DIN EN 61121.
**The values may differ from the those specified depending on the type of fabric, mixture of
laundry to be dried, residual moisture in the fabric and loading capacity.
Drum interior light
(bulb E14, 25 W)
(depending on model)
The drum is illuminated after the door is opened or closed, and also after the programme is
Drying time too long.
started. It goes out automatically. Replacing the bulb
Page 10.
(order from the after-sales service using the order number)
The humidity in the room
increases significantly.
Connection fittings for condensation outlet
The condensation is conveyed directly via a hose.
Mains failure.
One or more indicator lights for
Washer-dryer stack connection set
programme status are flashing.
The dryer can be placed on top of a suitable washing machine with the same width and depth
to save space. This connection set must always be used to secure the dryer to the washing
machine. With pull-out worktop: WTZ 11300.
The interior light is not working
Installation underneath the worktop
(depending on model).
Risk of electric shock!
Instead of the appliance covering plate, you must have a metal cover fitted by an expert.
9
Safety instructions
Emergency
– Pull the appliance plug out of the socket immediately or disconnect the fuse.
ONLY use the
– in rooms inside the house.
dryer...
– to dry fabrics.
The dryer must
– be used for other purposes than those described above.
NEVER...
– be modified in terms of its technology or attributes.
Dangers
– The dryer must not be used by children or persons who have not been
instructed in its use.
– Do not leave children unsupervised near the dryer.
– Keep pets away from the dryer.
– Remove all objects from pockets.
Make especially sure that cigarette lighters are removed as they constitute an
Mains plug plugged in?
explosion hazard.
Programme selected?
– Do not lean or sit on the door
and
Empty the condensation container.
Installation
– Secure loose cables
If featured, check hose for condensation outlet.
– Do not operate the dryer if there is a risk of frost.
Mains
– Connect the dryer according to specifications to an AC earthed socket, as
Start/Stop
Clean the fluff filter and/or air cooler under running water
connection
otherwise it cannot be guaranteed that the appliance is completely safe.
Page 4/6.
– The cable cross-section must be sufficient.
Start/Stop button selected?
Door closed?
– Only use earth-leakage circuit breakers with the following symbol:
Programme set?
– The appliance plug and socket must be compatible.
Ambient temperature greater than 5 °C?
– Do not use multiple plugs/couplings and/or extension cables.
Align dryer horizontally.
– Do not hold the appliance plug with wet hands
Clean air cooler seal.
– Never pull the appliance plug out of the socket by its cable.
Push the door closed until you hear it engage.
– Do not damage the mains lead
Operation
– Only load the drum with laundry.
Laundry load exceeded?
Remove articles of clothing immediately after
Check the contents before you switch the dryer on.
the end of the programme, hang up and pull into shape.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax,
Unsuitable programme selected
Page 7.
grease or paint (e.g. hair setting spray, nail polish remover, stain remover,
Warm laundry feels damper than it actually is.
cleaning solvent, etc.)
The selected programme does not suit the load. Use another
– Dust (e.g. coal dust, flour) poses a danger: do not use the dryer
drying programme or, in addition, select the time programme
explosion hazard.
Page 7.
– Do not put laundry containing foamed material/rubber in the dryer
Use fine adjustment for the drying result
Page 5/6.
Fine layer of limescale on the humidity sensors
material may be destroyed and the dryer may be damaged due to possible
Page 6.
deformation of the foamed material.
Clean the humidity sensors
Programme termination, e.g. tank full, mains power supply failure,
– Switch off the dryer once the programme has ended.
door open or maximum drying time reached.
– Condensation is not drinking water and may be contaminated with fluff.
Rinse the fluff filters under running water
Page 4.
Defect
– Do not use the dryer if it is defective or if you suspect it is.
Insufficient supply of air
ensure that air can circulate.
Repairs must only be carried out by the after-sales service.
Air inlet possibly blocked
Clear inlet
Page 8.
– Do not use the dryer if the mains cable is defective. To avoid danger, only
Ambient temperature higher than 35 °C
ventilate the room.
have the defective mains cable replaced by the after-sales service.
Make sure the room is sufficiently ventilated.
– Always pull the mains plug out of the socket before changing the bulb for the
interior light
Remove laundry from the dryer immediately and spread out.
Spare parts
– Only use genuine spare parts and accessories for safety reasons.
This allows the heat to dissipate.
Clean filter and air cooler
Page 4/6.
Disposal
– Dryer: pull out the appliance plug, then cut off the mains cable from the
Check installation conditions
Page 8.
appliance.
Switch off, leave to cool down, switch on again, restart
Dispose of at municipal waste disposal facility.
programme.
– Packaging: do not leave children alone with packing parts
Pull out the appliance plug, remove the cover cap in the interior
risk of suffocation.
above the door (use Torx 20 screw driver) and replace the bulb.
– All materials are environmentally sound and can be reused. Dispose of in an
Close the cover cap.
environmentally-responsible manner.
Never operate the dryer without a cover cap.
10
risk of tipping.
tripping hazard.
risk of electric shock.
risk of electric shock.
fire/explosion hazard.
elastic
Dryer
risk of electric shock.
en Instruction manual
11
ページを印刷する