Food residues can cause white deposits to form.
Note:
These are harmless and do not affect how the
appliance works. You can remove these residues using
lemon juice if required.
Cleaning self-cleaning surfaces
The self-cleaning surfaces are coated with a porous,
matte ceramic layer. This coating absorbs and dispels
splashes from baking and roasting while the appliance
is in operation.
If the self-cleaning surfaces no longer clean themselves
sufficiently and dark stains appear, they can be cleaned
using the cleaning function. To do this, refer to the
information in the relevant section. ~ "Cleaning
function" on page 25
Caution!
Do not use oven cleaner on self-cleaning surfaces. This
will damage the surfaces. If oven cleaner does get onto
these surfaces, dab it off immediately using water and a
sponge cloth. Do not rub the surface and do not use
abrasive cleaning aids.
Keeping the appliance clean
Always keep the appliance clean and remove dirt
immediately so that stubborn deposits of dirt do not
build up.
:
Warning – Risk of fire!
Loose food remnants, fat and meat juices may catch
fire. Before using the appliance, remove the worst of the
food remnants from the cooking compartment, heating
elements and accessories.
Tips
Clean the cooking compartment after each use. This
■
will ensure that dirt cannot be baked on.
Always remove flecks of limescale, grease, starch
■
and albumin (e.g. egg white) immediately.
Use the universal pan for baking very moist cakes.
■
Use suitable ovenware for roasting, e.g. a roasting
■
dish.
.Cleaning function
T he self-cleaning surfaces in the cooking compartment
C l e a n i n g f u n c t i o n
are cleaned with the "EcoClean" cleaning function.
The self-cleaning surfaces (back panel, ceiling panel
and side panels) are coated with a porous, matt
ceramic material. This coating absorbs and breaks
down splashes from baking, roasting and grilling while
the oven is in operation. If the surfaces no longer clean
themselves adequately and dark patches appear, the
surfaces can be cleaned by the cleaning function.
Cleaning recommendation
The appliance records how long it is in operation and
which operating mode is used. When cleaning is
recommended,
will appear on the display when the
'–
appliance is switched off. You can dismiss this
message by pressing any button except the
The prompt will continue to be displayed, however, until
the cleaning function has been run in full.
You can completely reset the cleaning
Note:
recommendation counter by pressing and holding the
button for approximately 4 seconds.
A
The prompt will not reappear until the appliance has
been used a certain number of times again.
Caution!
If you do not act on this cleaning recommendation, the
self-cleaning surfaces in the cooking compartment may
become damaged.
If your appliance is already very dirty, e.g. because you
have used it to cook fatty poultry or roasts, or if you
notice dark patches on the self-cleaning surfaces, do
not delay running the cleaning function until this prompt
appears. The more often or the earlier the appliance is
cleaned, the longer the self-cleaning surfaces will retain
their ability to clean themselves. You can clean the
cooking compartment at any time as required using the
cleaning function.
The counter for the cleaning recommendation
Note:
prompt will be reset following a power failure. It is
therefore a good idea to run the cleaning function after
a power failure has occurred.
Prior to initiating the cleaning function
Remove shelves, rails, accessories and ovenware from
the cooking compartment.
Cleaning the cooking compartment floor and the
inside of the appliance door
Remove the worst dirt from the cooking compartment
floor, the inside of the appliance door and the interior
lighting. Otherwise, patches will appear that can no
longer be removed.
Caution!
Do not use oven cleaner on the self-cleaning surfaces.
This will damage the surfaces. If oven cleaner does
come into contact with these surfaces, dab it off
immediately with water and a sponge cloth. Please to
Cleaning function
en
button.
A
25
ページを印刷する