- ページ 2

バリカン Andis BDP-120のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Andis BDP-120 2 ページ。 Сlipper/trimmer

ページを印刷する

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should

always be followed, including the following: Read all instructions

before using the Andis Clipper/Trimmer.

DANGER:

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug

immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be pulled

into a tub or sink. Do not place in or drop into water or other

liquid.

4. Always unplug this appliance from the electrical outlet immedi-

ately after using.

5. Unplug this appliance before cleaning, removing, or assem-

bling parts.

WARNING:

To reduce the risk of burns, fire, elec-

tric shock, or injury to persons:

1. An appliance should never be left unattended when plugged in.

2. Close supervision is necessary when this appliance is used by,

on, or near children or invalids.

3. Use this appliance only for its intended use as described in this

manual. Do not use attachments not recommended by Andis.

4. Never operate this appliance if it has a damaged cord or plug,

if it is not working properly, if it has been dropped or damaged,

or dropped into water. Return the appliance to an Andis Service

Center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray) products

are being used or where oxygen is being administered.

8. Do not use this appliance with a damaged or broken blade or

comb, as injury to the skin may occur.

9. To disconnect turn control to "off" then remove plug from

outlet.

10. If this clipper/trimmer has means for grounding, connect to a

properly grounded outlet only. See Grounding Instructions.

11. If used as an animal clipper/trimmer or shear: during use, do

not place or leave appliance where it may be:

(1) damaged by an animal or (2) exposed to the weather.

SAVE THESE INSTRUCTIONS

THIS PRODUCT INTENDED FOR PROFESSIONAL USE

(These instructions only apply for trimmers that have a 2-prong

plug). To reduce the risk of electric shock, this appliance has a

polarized plug (one blade is wider than the other). This plug will

fit in a polarized outlet only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician to install the proper outlet. Do not change the

plug in any way.

GROUNDING INSTRUCTIONS

(These instructions only apply for clipper/trimmers that have a 3-

prong plug). This appliance should be grounded. In the event of

an electrical short circuit, grounding reduces the risk of electric

shock by providing an escape wire for the electric current. This

appliance is equipped with a cord having a grounding wire with

an appropriate grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded in accordance with

all local codes and ordinances.

DANGER:

Improper use of the grounding plug

can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not

connect the grounding wire to either flat-blade terminal. The wire

with insulation having an outer surface that is green with or with-

out yellow stripes is the grounding wire. Check with a qualified

electrician or serviceman if the grounding instructions are not

completely understood, or if in doubt as to whether the appliance

is properly grounded. Do not modify the plug provided; if it will

not fit the outlet, have the proper outlet installed by a qualified

electrician. This appliance is for use on a nominal 120-volt circuit,

and has a grounding plug that looks like the plug illustrated in

Diagram A. A temporary adapter, which looks like the adapter

illustrated in Diagrams B and C, may be used to connect this plug

to a 2-pole receptacle as shown in Diagram B if a properly

grounded outlet is not available. The temporary adapter should be

used only until a properly grounded outlet (Diagram A) can be

installed by a qualified electrician. The green colored rigid ear,

lug, or the like extending from the adapter must be connected to

a permanent ground such as a properly grounded outlet-box

cover. Whenever the adapter is used, it must be held in place by a

metal screw.

GROUNDING METHODS

ADAPTER

GROUNDED

OUTLET

BOX

METAL

SCREW

TAB FOR

GROUNDING

SCREW

GROUNDING

Diagram A

Diagram B

OPERATING INSTRUCTIONS

Please read the following instructions before using your new

Andis clipper/trimmer. Give it the care that a fine precision built

instrument deserves and it will give you years of service. Before

starting clipper/trimmer remove blade guard (some models may

not have a blade guard). Plug cord into electrical outlet, operate

at 120 volt, 60 cycle AC electrical current or as noted on the unit.

To start clipper/trimmer move switch button to on position, to

stop, move switch button back to original position. After using

your Andis clipper/trimmer, rewrap cord and store in a safe place.

USER MAINTENANCE

The internal mechanism of your clipper/trimmer has been perma-

nently lubricated at the factory. Other than the recommended

maintenance described in this manual, no other maintenance

should be performed, except by Andis Company or an Andis

Authorized Repair Service Station.

POWER ADJUSTMENT FOR MODELS ML, & GC

Your Andis clipper/trimmer has been adjusted to line voltage at

the factory. However, because of voltage variations it may be nec-

essary to adjust the power setting for your area. If the power

adjustment is off, you will usually notice a "clatter", when the

clipper/trimmer is "on" or introduced into the hair. (It is normal

for your clipper/trimmer to "clatter" for an instant when initially

turned on).

TO ADJUST YOUR CLIPPER/TRIMMER:

1. Oil the blades (see Diagram D).

2. The power screw is located in

the lower part of the housing

opposite the switch (see

Diagram E).

OIL

3. Turn your clipper/trimmer

"on".

4. Using a standard screwdriver

that fits the slot, turn the

power screw counter clockwise until the clipper/trimmer clat-

ters continuously. Then turn the screw clockwise carefully until

the clatter ceases.

5. Your clipper/trimmer is now adjusted to its optimum power

setting.

POWER ADJUSTMENT FOR MODEL SM

POWER

SCREW

POWER ADJUSTMENT FOR MODELS

ML, GC

Diagram C

POWER SCREW

Diagram E

CARE AND SERVICING OF YOUR ANDIS

CLIPPER/TRIMMER BLADES

Blades should be oiled before, during, and after each use. If your

clipper/trimmer blades leave streaks or slow down, it's a sure

sign blades need oil. The clipper/trimmer should be held in a

position shown at right to prevent oil from getting into motor.

Place a few drops of Andis Clipper Oil on the front and side of the

cutter blades (see Diagram D). Wipe excess oil off blades with a

soft dry cloth. Spray lubricants contain insufficient oil for good

lubrication, but are an excellent clipper coolant. Always replace

broken or nicked blades to prevent injury. You can clean the

excess hair from your blades by using a small brush or worn out

toothbrush. To clean the blades we suggest to immerse the

blades only into a shallow plan of Andis Clipper Oil, while the

clipper is running. Any excess hair and dirt that has accumulated

between the blades should come out. After cleaning, turn your

OIL

clipper/trimmer off and dry blades with a dry cloth and start clip-

ping again.

OIL

PLEASE NOTE:

Persons familiar with replacing and adjusting ANDIS Models ML,

& GC, blades, please read the following blade replacement

Diagram D

instructions. Those persons not familiar with this procedure,

please return clipper/trimmer to your supplier or Andis Authorized

Repair Station for blade replacement and adjustment.

FOR MODELS ML & GC

Unplug clipper, turn clipper/trimmer

over around and place on hard, flat

surface so teeth of clipper face down.

Unscrew blade screws with standard

screwdriver (see Diagram F). Remove

lower blade. Place thumb and forefin-

ger on upper blade (see Diagram G)

push upper blade with thumb to one

side of clipper/trimmer while your fore-

finger unsnaps blade from the connect-

ing fork. (cover of clipper/trimmer

removed in picture to show detail only.

It is not necessary to remove cover

when changing blades.) To install new

blade set (keep clipper unplugged)

remove upper blade (smaller of the set)

from the wrapped package. Place the upper blade towards the

connector fork. Slant the blade slightly so one side of the upper

angle (white nylon bracket on upper blade) "hooks" onto one

prong of the connector fork, making sure the small indentation on

Diagram F

Diagram G