- ページ 3
バリカン Andis Ultra MC-2のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Andis Ultra MC-2 12 ページ。 Andis company model mc-2 hair clipper - use and care guide
Andis Ultra MC-2 にも： パンフレット (2 ページ), パンフレット (1 ページ), 仕様 (1 ページ), 仕様 (1 ページ), 使用とケア (2 ページ)
ページを印刷する
and give you precise control of hair lengths. The length of trim is indicated
on the attachment comb. Use the chart to find the approximate lengths of
cut. Different blade angles in relation to the skin, thickness and texture of
the hair will vary the cutting length.
CLIPPER BLADE ADJUSTMENT
Your Andis adjustable clipper blade set is easy to adjust. From coarse to
fine cuts, all that is needed is a flick of the adjustment lever with your
thumb. In the upright position, the blades are set for the finest, or shortest
cuts (Figure C).
USER MAINTENANCE
The internal mechanism of your clipper has been permanently lubricated at
the factory. Other than the recommended maintenance described in this
manual, no other maintenance should be performed, except by Andis
Company or an Andis authorized service station. To find an Andis
authorized service station near you log on to www.andis.com or contact
our customer service department at 1-800-558-9441.
POWER ADJUSTMENT
Your Andis clipper has been adjusted to line voltage at the factory. However,
because of voltage variations, it may be necessary to adjust the power
setting for your area. If the power adjustment is off, you will usually notice a
"clatter" when the clipper is on or introduced into the hair. (It is normal for
your clipper to "clatter" for an instant when initially turned on).
TO ADJUST YOUR CLIPPER'S POWER SCREW
1. Oil the blades.
2. The power screw is located in the lower part of the housing opposite the
switch (Figure D).
3. Turn your clipper ON.
4. Using a standard flathead screwdriver that fits the slot, turn the power
screw clockwise until the clipper clatters continuously. Then turn the
screw counterclockwise carefully until the clatter ceases.
5. Your clipper is now adjusted to its optimum power setting.
BLADE TEMPERATURE
Due to the high speed nature of Andis clippers, please check for blade heat
often, especially on close cutting blades. If blades are too hot, dip the
blades only into Andis Blade Care Plus or apply Andis Cool Care Plus and
then Andis Clipper Oil.
4
A
C
D
ADJUSTMENT
LEVER
POWER
SCREW
CLIPPING GUIDE
Description
Clipping Direction
With hair grain
Standard Andis Blade
Against hair grain
With hair grain
1/16" Attachment Comb
Against hair grain
With hair grain
1/8" Attachment Comb
Against hair grain
With hair grain
1/4" Attachment Comb
Against hair grain
With hair grain
3/8" Attachment Comb
Against hair grain
With hair grain
1/2" Attachment Comb
Against hair grain
With hair grain
3/4" Attachment Comb
Against hair grain
With hair grain
1" Attachment Comb
Against hair grain
B
SNAP!
E
OIL
Approximate Length of Cut
Blade set to
Blade set to
shortest cut
longest cut
1/16" (1.6 mm)
3/16" (4.8 mm)
1/32" (0.8 mm)
1/8" (3.2 mm)
3/16" (4.8 mm)
5/16" (7.9 mm)
3/32" (2.4 mm)
5/32" (4.0 mm)
1/4" (6.4 mm)
3/8" (9.5 mm)
1/8" (3.2 mm)
1/4" (6.4 mm)
3/8" (9.5 mm)
1/2" (12.7 mm)
1/4" (6.4 mm)
3/8" (9.5 mm)
1/2" (12.7 mm)
5/8" (15.9 mm)
3/8" (9.5 mm)
1/2" (12.7 mm)
5/8" (15.9 mm)
7/8" (22.2 mm)
1/2" (12.7 mm)
5/8" (15.9 mm)
7/8" (22.2 mm)
1-1/8" (28.6 mm)
3/4" (19.0 mm)
1" (25.4 mm)
1-1/8" (28.6 mm)
1-3/8" (34.9 mm)
1" (25.4 mm)
1-1/4" (31.8 mm)
5