- ページ 4

業務用食品機器 Andis AG2のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Andis AG2 12 ページ。 Andis company model ag2 hair trimmer - use and care guide
Andis AG2 にも：仕様 (2 ページ), 使用とケア (2 ページ)

ページを印刷する

in the guide slot of the tension spring (Figure E). Now slide the upper blade to

the opposite side of the lower blade and repeat this process. After completing

this procedure, slide the upper blade, centering it over the lower blade. Handle

or store your Andis Clipper with the blades down so excess oil will not run into

the clipper case.

CHANGING THE BLADE DRIVE ASSEMBLY

If your clipper blades no longer cut properly (be sure to try more than one blade,

since the blade currently being used may be dull), it could be that your blade

drive assembly needs replacement.

To change the blade drive assembly:

1. Remove blade set (Figure A).

2. Remove drive cap (Figure F).

3. Remove blade drive mounting screws (Figure G).

4. NOTE: Before removing blade drive assembly, note the way it is positioned

(this will help you in reassembly). Remove blade drive assembly (Figure H).

5. Drive bearing should be at its lowest position, if not, move it with your finger

to lowest position (Figures I & J).

6. Put on new drive assembly, align screw holes and press down (Figure H).

7. Reassemble blade drive by mounting screws (Figure G).

8. Replace drive cap (Figure F).

9. Replace blade (Figure C).

REPLACEMENT OF CARBON BRUSHES

WARNING: Clipper must be unplugged before removing carbon brush caps or

performing any maintenance, as electrical shock may occur. The carbon brushes

of your clipper should be checked every three to six months. Carbon brush

replacement should be performed when the carbon brushes reach no less than

1/16" in length. To replace the carbon brushes, unscrew brush caps with a

standard screwdriver. Do one side at a time.

Caution: the carbon brushes are spring loaded. Take precaution when

unscrewing the brush caps from the unit. The brush spring should be in plain

view upon removing the cap. Pull out the spring and brush from its canal, then

remove old carbon brush. Tip the clipper to one side so the carbon brush slides

out. Be sure to note the way the brush is inserted so that if it does not need

replacing, it may be re-inserted in exactly the same position. When placing a

new carbon brush into the carbon brush canal, make sure to align the curvature

on the end of the carbon brush with the curve of the commutator seen at the

bottom of the canal (Figure K). When aligned properly, the two beveled edges of

the carbon brush will be located in the upper right and lower left corners. Be

sure to insert the beveled end of the carbon brush into the canal first. Failure to

perform this procedure correctly may cause the carbon brushes to not seat

themselves properly against the commutator. Replace the carbon brush spring

into the brush cavity after the carbon brush has been installed, then replace

(MODEL AG2 ONLY)

carbon brush cap with a standard size screwdriver. Turn clockwise only until you

feel the brush cap stop. If the brush cap is tightened too tightly, it will force the

brush spring past the carbon brush and will cause damage to the commutator.

SERVICING OF A DOUBLE-INSULATED CLIPPER

In a double-insulated clipper, two systems of insulation are provided instead of

grounding. No grounding means is provided on a double-insulated clipper, nor

should a means for grounding be added. Servicing a double-insulated clipper

requires extreme care and knowledge of the system, and should be done only by

an Andis Authorized Service Station. Replacement parts must be identical to

those parts being replaced. A double-insulated clipper is marked by the words

"double insulation" or "double insulated". The symbol

on the appliance.

FACTORY REPAIR SERVICE

When the blades of your Andis clipper become dull after repeated use, it is

advised to purchase a new set of blades available through your Andis supplier or

through an Andis Authorized Service Station. Some blade sets can be

resharpened – contact Andis Company for information on resharpening. To find

an Andis Authorized Service Station near you log on to www.andis.com or

contact our customer service department: 1-800-558-9441 (U.S.) or

1-800-335-4093 (Canada).

Caution: Never handle your Andis clipper while you are operating a water

faucet, and never hold your clipper under a water faucet or in water. There is

danger of electrical shock and damage to your clipper. Andis Company will

not be responsible in case of injury due to this carelessness.

may also be marked