- ページ 11
サブウーファー Atlantic Technology 10 CSBのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Atlantic Technology 10 CSB 12 ページ。 Corner subwoofer
Atlantic Technology 10 CSB にも： 製品情報シート (2 ページ)
ページを印刷する
Instruction Manual
Painting the Cabinets
STATUS
LEVEL
L/MONO
LOW
MIN
MAX
LEVEL
RIGHT
FREQ
NORMAL
BYPASS
50
160
LOWPASS
PHASE
OFF
AUTO
ON
STDBY
0
180
INPUT
HIGH
LEVEL
OUTPUT
-
-
+
+
RIGHT
L/MONO
110-120V
220-240V
CAUTION
POWER
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: SHOCK HAZARD-DO NOT OPEN
ON
OFF
AVIS:RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLICANCE TO RAIN OR MOISTURE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
For the finish coat, we recommend using a latex water-based paint.You
may use a brush, pad, roller, or spray paint, depending on the type of
finish effect desired. For best results apply two light coats of the final
color.Make sure the first coat is completely dry before applying the sec-
ond coat.
IMPORTANT: Please don't get paint on the amplifier. Also, don't
paint the driver recess area of the cabinet or risk getting any paint
on the acoustical foam or the driver itself, as this may seriously
degrade the unit's performance and void the warranty.
During painting, please protect these areas with paper and mask-
ing (painter's) tape. For best results, remove while the paint is still
wet.
Subwoofer Troubleshooting Guide
Once your subwoofer is set up, you should have many years of maintenance free enjoyment from your system. However, if you should encounter a
problem, refer to the following guide to help you find the solution. If a problem persists, you should contact your local authorized Atlantic Technol-
ogy dealer.
Problem
No bass output
Audible buzz or hum
The cabinet may be painted to
blend in even better with your
room's décor. First,clean the cab-
inet,using an appropriate cleaner
such as non-ammonia Windex®
or diluted Simple Green®. Then
use a coat of primer, such as
Glidden® interior/exterior Grip-
per® or Rust-Oleum® Rusty
Metal Primer. Be sure to follow
the primer's instructions.
Possible Cause
AC power cord unplugged or
plugged into a non-working outlet.
Input cables not securely
connected or defective.
Receiver/Processor's sub-out is muted,
due to incorrect configuration of speaker
setup menu.
Input cable not securely connected
or defective.
Ground loop through antenna or
cable TV system input.
Specifications
Type
Sealed enclosure, down-firing
Bass driver
10" (254mm) long-throw
Frequency response
30-250Hz, +/- 3dB
Amplifier power
180 RMS
Peak output
106dB in 2000 cu.ft.
Dimensions (WxHxD)
22 x 19½ x 12"
559 x 496 x 305mm
Weight
35 lbs (16 kg)
Specifications are those in effect at the time of printing. Atlantic Tech-
nology reserves the right to change specifications or designs at any time
without notice.
Possible Solution
Plug into a working outlet.
Check all connections, then try another
input cable.
Check that receiver/processor is configured
so that all speakers are set to "small" and
sub is "on."
Check all connections, then try another
input cable.
Test by disconnecting antenna and/or cable
system input leads. If hum goes away, install
isolation balun(s) at that point.
Specifications
11