Installation and connection
en
Faults in the gas installation/smell of gas
If you notice a smell of gas or faults in the gas
installation, you must
immediately shut off the gas supply and/or close the
■
gas cylinder valve
immediately extinguish all naked flames and
■
cigarettes
switch off electrical appliances and lights
■
open windows and ventilate the room
■
call the aftersales service or the gas supplier
■
Moving the appliance by the gas line or door handle
Do not move the appliance while holding the gas line;
the gas pipe could be damaged. There is a risk of a gas
leak! Do not move the appliance while holding it by the
door handle. The door hinges and door handle could
be damaged.
Electrical connection
The appliance is designed to operate at 220-240 V. A
16 A fuse is required for connection.
Have the appliance installed by your after-sales service.
Any damage arising from the appliance being
connected incorrectly will invalidate the warranty.
Caution!
If the electricity supply drops below 180 V, the
■
electrical ignition system does not work.
If the supply cord is damaged, it must be replaced
■
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
:
Warning – Danger of death!
There is a risk of electric shock if you touch live
components.
Always make sure your hands are dry when you
■
touch or hold the mains plug.
Only pull out the mains cable by taking hold of the
■
plug and removing the plug; never pull it out by the
mains cable itself, as this could damage it.
Never unplug the mains plug when the appliance is
■
in operation.
Please note the following information and ensure that:
Notes
The mains plug fits the socket.
■
The cable cross section is adequate.
■
The earthing system is properly installed.
■
The mains cable is only replaced by a qualified
■
electrician (if this is necessary).Spare mains cables
can be ordered from our after-sales service.
No power strips/multi-way connectors or extension
■
cables are used.
If using a residual current device, only use one that
■
bears the mark
.
z
The presence of this mark is the only way to be sure
that it fulfils all the applicable regulations.
The mains plug can be accessed at all times.
■
The mains cable is not kinked, crushed, modified or
■
severed.
The mains cable does not come into contact with
■
heat sources.
10
For the after-sales service
Caution!
The appliance must be connected in accordance
■
with the data on the rating plate.
Only connect the appliance to an electrical
■
connection that meets the applicable provisions. The
socket must be easily accessible so that you can
disconnect the appliance from the electricity supply
if necessary.
Please ensure the availability of a multi-pin
■
disconnecting system.
Never use extension cables or multiple plugs.
■
For safety reasons, this appliance must only be
■
connected to an earthed connection. If the safety
earth terminal does not comply with regulations,
safety against electrical hazards is not guaranteed.
An all-pole isolating switch with a contact gap of at
■
least 3 mm must be present in the installation circuit.
This is not necessary if the appliance is connected
by a plug that is accessible to the user.
Electrical safety: The cooker corresponds to safety
■
class I and may only be used in conjunction with a
safety earth terminal.
You must use a H 05 W-F type cable or equivalent
■
for the appliance connection.
The mains voltage must correspond to the voltage
specified on the rating plate.
Caution!
All appliances with a three-wire cable must be
earthed.
Connect the wires in the power cord according to the
colour coding:
Explanaions
Green and yellow
earth wire
Blue
(null) neutral wire
Brown
phase (external conductor)
If the power cord is replaced
Note:
Only connect it to the appliance as shown in the
connection diagram.
Levelling the cooker
Always place the cooker directly on the floor.
The cooker has height-adjustable feet. This allows you
to raise the plinth by about 15 mm. Please observe the
special installation instructions.
Adjacent units
Any adjacent units must not be made of flammable
materials. The fronts of any adjacent units must be heat-
resistant up to at least 90 °C.
Wall fixing
To prevent the cooker from tipping over, you must fix it
to the wall using the enclosed bracket. Please observe
the installation instructions for fixing the oven to the
wall.
<
ページを印刷する