- ページ 28

冷蔵庫 Bosch Series 4のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch Series 4 50 ページ。 Free standing cooker
Bosch Series 4 にも: 取扱説明書 (24 ページ), 取扱説明書 (44 ページ), 取付・使用説明書 (16 ページ), 取付・使用説明書 (16 ページ), 取扱説明書 (16 ページ), 取扱説明書 (24 ページ), 取扱説明書 (10 ページ), 取扱説明書 (12 ページ), 取扱説明書 (20 ページ), 取扱説明書 (32 ページ), 取付説明書 (12 ページ), マニュアル (2 ページ), クイック・リファレンス・マニュアル (2 ページ), ユーザーマニュアル (16 ページ), ご利用案内 (24 ページ), 取扱説明書 (48 ページ), ご利用案内 (32 ページ), ご利用案内 (32 ページ), ユーザーマニュアル (32 ページ), ご利用案内 (32 ページ), 取扱説明書 (24 ページ), 取扱説明書 (27 ページ), ユーザーマニュアルと設置手順 (40 ページ), ご利用案内 (32 ページ), 取扱説明書 (36 ページ), ユーザーマニュアル (24 ページ), 取扱説明書 (47 ページ), ユーザーマニュアルと設置手順 (28 ページ)

Bosch Series 4 取扱説明書
en Operating the appliance

Switching on the appliance

Turn tap fully on.
1.
Switch on ON/OFF switch (.
2.
The Eco 50° programme has been
preset for environmentally friendly
operation whenever the appliance
starts. This programme remains
selected if no other programme
button 0 is pressed.
Press START button P.
3.
Programme sequence starts.
Note:
For ecological reasons the Eco 50°
programme is preset whenever the
appliance starts. This conserves
environmental resources and not least
saves you money.
The Eco 50° programme is a
particularly environmentally friendly
programme. According to EU
regulation 1016/2010 it is the
"Standard programme" which is the
most efficient standard cleaning cycle
for cleaning normally soiled utensils in
terms of the combined energy and
water consumption for cleaning these
types of utensils.
28
Remaining running time
display
When the programme is selected, the
remaining programme time is indicated
in the display window )".
The running time is determined during
the programme by the water
temperature, the quantity of dishes as
well as the degree of soiling and may
vary (depending on the selected
programme).

Time preselection *

* depending on the configuration of
T i m e p r e s e l e c t i o n
your specific dishwasher
You can delay the start of the
programme in hourly steps by up to 24
hours.
Here's how to set up the delay:
Switch on ON/OFF switch (.
1.
Press the timer programming button
2.
@ + repeatedly until )" œ ‹‚
appears in the display window.
Keep pressing the timer
3.
programming button @ - or + until
the desired time is displayed.
Press START button P.
4.
The delay timer has been activated.
To clear the specified delay, press
5.
the button @ - or + repeatedly until
)" œ ‹‹ appears in the display
window.
Until the programme has started, you
can change your selection in any way
you like.

Programme end

The programme has finished when the
value ‹:‹‹ appears in the display
window )".