- ページ 2

スピーカーシステム Atlas FAP42T-BのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Atlas FAP42T-B 5 ページ。 Strategy series ii 4 inch loudspeaker system

ページを印刷する

General Description

The FAP42T's 130˚ dispersion angle effectively reduces the number of

loudspeakers necessary to achieve coverage in distributed systems with

low ceilings.

The loudspeaker component matches the performance of the legendary

Atlas Sound Strategy FA Series. High quality construction 4" coaxial cone

type driver includes a 1" voice coil and polypropylene cone with a butyl

rubber surround. The 19mm coaxially mounted tweeter is constructed

of PEI. A high sensitivity level means less power may be required to

achieve the desired SPL. This loudspeaker is factory assembled in an

optimally tuned & ported deep drawn enclosure and includes a specially

designed 16 Watt low saturation 70.7V / 100V transformer. A convenient

front mounted selector switch allows tap selection without the need to

remove the speaker from the ceiling. This switch also includes a trans-

former bypass setting for 8Ω direct coupled operation.

Mounting Accessories

Mounting is simplified with Strategy style "Dog Leg" tabs that allow

easy installation into drop tile or drywall ceilings with provided tile bridge

assembly. The tile bridge consists of two "V" shaped formed mounting

rails and a C-Ring assembly. The C-Ring can be attached to the rails with

the screws provided to extend support to the T-Bar grid in suspended

ceiling applications. Multiple hole locations are provided to allow the

C-Ring to be positioned to the outer edge the tile if necessary.

For existing dry-wall applications the tile bridge C-Ring and support rails

can be inserted into the hole cut for the FAP42T. For easy positioning the

"V" shaped support rails match the shape of the C-Ring tabs for easy

maneuvering and location when working "blindly" above the deck

A uniquely designed "easy access" input panel on the side of the enclo-

sure allows for "thru" conduit runs using flexible or rigid conduit. Below

this cover resides a detachable Phoenix style locking four-pole connec-

tor which provides for easy daisy chain wiring to other full range 70.7V

loudspeakers or Atlas Sound FASUB subwoofer. The package includes an

attractive press-fit grille which nicely matches contemporary architecture.

For new construction drywall ceiling applications, the optional FAP42-TR

trim ring is available. This unit provides a marked location for drywall

installers to cut around essentially reserving the desired location in the

ceiling until final installation of FAP42T. Mounting holes are provided to

accommodate 16" or 24" OC stud / joist mounting.

A support ring is also provided on the top of the FAP42T enclosure to

facilitate an auxiliary support cable.

NOTE: IT IS MANDATORY THAT THIS SECONDARY SUPPORT

BE UTILIZED IN DROP CEILINGS FOR SAFETY AND SEISMIC

CONSIDERATIONS).

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333

FAX (800) 765-3435

Architect & Engineer Speciﬁcations

System shall include a high performance 4" coaxial loudspeaker,

ported bass reflex enclosure and press-fit grille for conventional ceiling

installation.

Frequency response for the system shall be 75Hz – 20kHz (±7dB).

Sensitivity shall be 88dB average. Loudspeaker shall be comprised of a 4"

coaxial cone driver constructed of polypropylene with a butyl rubber sur-

round. The 19mm tweeter shall be constructed of PEI. Magnet shall be a

minimum of 10oz. (264g) and the voice coil diameter shall be 1" (25mm).

Transformer shall be a 70.7V / 100V type with 1, 2, 4, 8, and 16 watt pri-

mary taps (@70.7V) with a front mounted tap selector switch to include a

transformer bypass setting for 8Ω / direct coupled operation.

Enclosure shall be a deep drawn steel enclosure design. Internal volume

shall be 285 in

. To facilitate connection in conduit systems, enclosure

shall be equipped with an access panel covering a recessed terminal cup.

This cover shall provide a combination

(25mm inside diameter) knock-out on the side access and a top access

compression fitting / strain relief to facilitate flexible conduit up to 22mm

outside diameter or 1 in (25mm inside diameter) conduit when the com-

pression fitting is removed.

External wiring shall be accomplished via a removable lockable wiring

connector with screw-down terminals to provide both secure wire termi-

nation and pre-wiring capability before loudspeaker installation. The 4-pole

locking connector shall facilitate in / out connections and shall be located

in the recessed area behind the conduit access panel.

Seismic support eye shall be provided on top of enclosure for addi-

tional suspension point when used in drop tile ceilings. Construction of

enclosure shall be a minimum of 18-gauge, deep drawn galvanized metal.

The system shall include a support backing plate to reinforce the ceil-

ing material and tile support rails for use on either 2' x 4' (609mm x

1219mm) or 2' x 2' (609mm x 609mm) suspended ceiling tiles. This

assembly can all be installed from beneath the ceiling tile.

Overall front face diameter shall not exceed 10

from the bottom of the ceiling shall not exceed 8

be press-fit, manufactured from 24-gauge perforated steel mesh and fin-

ished in white epoxy. Round grille shall be 8

The loudspeaker shall be the Atlas Sound FAP42T.

C-Ring / V-Rails

FAP42-TR

AtlasSound.com

⁄

" (19mm inside diameter) / 1"

⁄

" (267mm); overall depth

⁄

" (225mm). Grilles shall

⁄

" (214mm) diameter.

2/4