- ページ 11

掃除機 Bosch Series 4のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch Series 4 16 ページ。 Free standing cooker
Bosch Series 4 にも： 取扱説明書 (24 ページ), 取扱説明書 (44 ページ), 取付・使用説明書 (16 ページ), 取付・使用説明書 (16 ページ), 取扱説明書 (24 ページ), 取扱説明書 (10 ページ), 取扱説明書 (12 ページ), 取扱説明書 (20 ページ), 取扱説明書 (32 ページ), 取付説明書 (12 ページ), マニュアル (2 ページ), クイック・リファレンス・マニュアル (2 ページ), ユーザーマニュアル (16 ページ), 取扱説明書 (50 ページ), ご利用案内 (24 ページ), 取扱説明書 (48 ページ), ご利用案内 (32 ページ), ご利用案内 (32 ページ), ユーザーマニュアル (32 ページ), ご利用案内 (32 ページ), 取扱説明書 (24 ページ), 取扱説明書 (27 ページ), ユーザーマニュアルと設置手順 (40 ページ), ご利用案内 (32 ページ), 取扱説明書 (36 ページ), ユーザーマニュアル (24 ページ), 取扱説明書 (47 ページ), ユーザーマニュアルと設置手順 (28 ページ)

ページを印刷する
Bosch Series 4 取扱説明書

3Trouble shooting

Faults often have simple explanations. Please read the
T r o u b l e s h o o t i n g
notes in the table before calling the after-sales service.
The electronics of your hob are underneath the control
panel. For various reasons, the temperature in this area
may rise sharply.
Display
Fault
None
The power supply has been disconnected.
All displays flash
The touch control is wet or an object is resting
on it.
Several hotplates have been used over a pro-
"ƒ
longed period at high power settings. To pro-
tect the electronics, the hotplate has been
switched off.
"...
Despite the switch-off by
have become hot again. All hotplates have
therefore been switched off.
Warning: There is a hot pan in the area of the
"†
and the heat setting
control panel. There is a risk that the electron-
flash alternately. An
ics will overheat.
audible signal can be
heard
There is a hot pan in the area of the control
"†
and audible signal
panel. To protect the electronics, the hotplate
has been switched off.
The hotplate was in operation for too long and
"‰
has switched itself off.
Demo mode is switched on
š"
The hotplates do
not heat up

E-report in the displays

When an error message with "E" appears in the display,
e.g. E0111, switch the appliance off and on again.
If it was a one-off error, the display goes out. If the error
message appears again, call the after-sales service and
quote the exact error message.
A
flashes in the hotplate indicators
If
flashes in the hotplate indicators when the
A
appliance is connected to the mains or following a
power cut, the electronics are malfunctioning. To
acknowledge the fault, briefly cover the controls with
your hand.
In order that the electronics do not overheat, the
hotplates are switched off as and when necessary. The
"ƒ
œ
Measure
Check the household fuse for the appliance. Check whether there is a
power cut by trying other electronic appliances.
Dry the control or remove the object.
Wait a while. Touch any touch control. When
have cooled down sufficiently. You can continue cooking.
"ƒ
, the electronics
Wait a while. Touch any touch control. When
tinue cooking.
Remove the pan. The fault display goes out shortly afterwards. You can
continue cooking.
Remove the pan. Wait a while. Touch any control. When
can continue cooking.
You can switch the hotplate back on again immediately.
Switching off the demo mode: Disconnect the appliance for 30 seconds
from the power supply (switch off the household fuse or the circuit breaker
in the fuse box). Touch any touch control after 3 minutes. The demo mode
is switched off.
,
, or
display appears alternately with the
"...
"†
residual heat indicator.
Trouble shooting
en
or
•
"ƒ
goes out, the electronics
"...
goes out, you can con-
"†
goes out, you
11