- ページ 35

掃除機 Bosch Series 4のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch Series 4 48 ページ。 Free standing cooker
Bosch Series 4 にも： 取扱説明書 (24 ページ), 取扱説明書 (44 ページ), 取付・使用説明書 (16 ページ), 取付・使用説明書 (16 ページ), 取扱説明書 (16 ページ), 取扱説明書 (24 ページ), 取扱説明書 (10 ページ), 取扱説明書 (12 ページ), 取扱説明書 (20 ページ), 取扱説明書 (32 ページ), 取付説明書 (12 ページ), マニュアル (2 ページ), クイック・リファレンス・マニュアル (2 ページ), ユーザーマニュアル (16 ページ), 取扱説明書 (50 ページ), ご利用案内 (24 ページ), ご利用案内 (32 ページ), ご利用案内 (32 ページ), ユーザーマニュアル (32 ページ), ご利用案内 (32 ページ), 取扱説明書 (24 ページ), 取扱説明書 (27 ページ), ユーザーマニュアルと設置手順 (40 ページ), ご利用案内 (32 ページ), 取扱説明書 (36 ページ), ユーザーマニュアル (24 ページ), 取扱説明書 (47 ページ), ユーザーマニュアルと設置手順 (28 ページ)

ページを印刷する
Bosch Series 4 取扱説明書
Fault
Fault code ":ƒ... is lit.
Fault code ":Ġ is lit.
Fault code ":ƒˆ is lit.
A different fault code is
indicated on the digital
display.
(":‹‚ to ":„‹)
p or • appears on the
digital display )". *
Refill indicator for salt `
and/or rinse aid h is lit.
Refill indicator for salt `
and/or rinse aid h is not
lit.
The Machine Care display
lights up. *
Water is left in the
appliance at the end of the
programme.
* depending on the configuration of your specific dishwasher
Reason
Waste-water hose kinked or
blocked.
Siphon connection still sealed.
Cover on the waste water pump
loose.
Waste water pump blocked or
cover on the waste water pump is
not locked in position.
Mains voltage too low.
A technical fault has probably
occurred.
Not a fault!
No rinse aid.
No salt.
Sensor does not detect salt
tablets.
Refill indicator switched off.
There is still enough special
salt/rinse aid available.
Machine Care is recommended.
Filter system or area under the
filters 1Z is blocked.
Programme has not yet finished
Fault, what to do? en
Remedial action
Install hose without kinks, remove any
residue.
Check connection to siphon and open if
required.
Lock cover correctly. ~ "Waste water
pump" on page 33
Clean pump and lock cover correctly.
~ "Waste water pump" on page 33
No appliance fault, have the mains voltage
and electrical installation checked.
Switch off the appliance with the ON/OFF
switch (. After a short time restart the
appliance.
If the problem recurs, turn off water supply
and pull out the mains plug.
Call customer service and quote the fault
code.
See turboSpeed 20 min. in the chapter
"Overview of programmes". *
Refill rinse aid.
Refill with special salt.
Use different special salt.
Activation/deactivation (see chapter
"Water softening system/Special salt"
~ Page 12 or "Rinse aid" ~ Page 14).
Check refill indicator, levels.
Run the Machine Care programme using a
special dishwasher cleaning agent and
without loading any utensils.
The display will go out automatically after
three wash cycles whether or not the
Machine Care programme is carried out.
Clean filters and area underneath.
Wait until programme ends or reset.
35