- ページ 4

スピーカーシステム Bose 301 Series IVのPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Bose 301 Series IV 12 ページ。 Direct/reflecting speakers
Bose 301 Series IV にも：オーナーズマニュアル (12 ページ), オーナーズマニュアル (12 ページ), オーナーズマニュアル (13 ページ)

ページを印刷する

1. Specifications

DISASSEMBLY/ASSEMBLY PROCEDURES

Note: Refer to Figure 3 for the following proce-

dures.

1. Grille Removal: Both the front grille (1) and the

side grille (3) are held in place by a snap-fit and

are easily removed by hand. To remove,

CAREFULLY pull the grille away from the

speaker.

2. Woofer Removal/Replacement:

2.1 Remove the front grille as indicated in Proce-

dure 1.

2.2 Remove the 4 screws (11) holding the woofer

(9) in place.

2.3 Lift the woofer out and cut the wires connected

to the woofer terminals as close to the terminals

as possible.

2.4 Strip the wires and connect to the replacement

woofer. Make sure that the Red wire is con-

nected to the positive (+) terminal, both Black

wires are connected to the negative (-) terminal

and both Yellow wires are connected to the

woofer's "dummy" terminal, (no solder joint at

this terminal). Dress or twist wires to prevent

buzzing.

2.5 Remount the woofer to the cabinet using the

four screws.

3" Tweeter Removal/Replacement: In order

to remove the tweeter it will first be necessary to

remove the woofer from the enclosure.

Note: The positive terminal of the tweeter is

marked with a Red dot.

3.1 Remove both the front and side grilles as

indicated in Procedure 1.

3.2 Remove the 4 screws that secure the woofer to

the enclosure and lift the woofer away from its

opening.

3.3 Remove the #8-32 screw (6) from the back of

the gasket backed tweeter (4) and separate the

tweeter from the molded bracket portion of the

endcap.

3.4 Cut the wires connected to the tweeter as close

to the tweeter terminals as possible.

3.5 Strip the wires and connect the replacement

tweeter. Make sure the Yellow wire is con-

nected to the positive (+) terminal and the Black

wire is connected to the negative terminal (-).

3.6 Remount the tweeter using the #8-32 screw.

3.7 Remount the woofer using the four #8-11

screws.

4. 2" Tweeter Removal/Replacement: In order to

remove the tweeter it will first be necessary to

remove the woofer from the enclosure.

Note: The positive terminal of the tweeter is

marked with a Red dot.

4.1 Remove the front grille only, as indicated in

Procedure 1.

4.2 Remove the 4 screws that secure the woofer to

the enclosure and lift the woofer away from its

opening.

4.3 Remove the #8-32 screw from the back of the

gasket backed tweeter (12) and separate the

tweeter from the molded bracket portion of the

endcap.

4.4 Cut the Yellow wire and the lamp lead con-

nected to the tweeter as close to the tweeter

terminals as possible.

4.5 Strip the Yellow wire and connect the replace-

ment tweeter. Make sure the Yellow wire is

connected to the negative (-) terminal and the

lamp is connected to the positive terminal (+).

Note: To replace just the lamp or both the tweeter

and lamp it will be necessary to remove the tweeter

by following procedures outlined in section 4.