- ページ 11
アンプ Bose 2060のPDF インストーラーズマニュアルをオンラインで閲覧またはダウンロードできます。Bose 2060 40 ページ。 Commercial power amplifiers
4.2 Rear panel (cont.)
CAUTION
AVIS
RISK OF ELECTRICAL SHOCK
RISQUE DE CHOC ELECTRIQUE
DO NOT OPEN COVER,
NE PAS OUVRIR CE CARTER,
AUTHORIZED PERSONNEL
RESERVE AU PERSONNEL
ONLY.
AUTORISE.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
This device complies with part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference and (2) this device must
accept any interference received, including interference which may cause undesired operation.
Complies with Canadian ICES-003 Class A specifications.
120VAC, 4.6A max.
60 Hz
600W
SERIAL No.:
®
D.O.M.:
Model 2150
BOSE CORPORATION
FRAMINGHAM, MA 01701-9168 U.S.A.
MADE IN U.S.A. OF DOMESTIC AND FOREIGN COMPONENTS.
10
7
1
Standard Input Module
2
Input Connectors
3
EQ Out Connectors
3. EQ out connectors
A
1
⁄
" TRS output connector provides access to an equalized line level output signal for each
4
channel. If equalizer cards are installed, this signal has passed through the internal equal-
izer, but has not passed through the amplifier itself. (For additional information on EQ cards,
see Input Modules on page 10.)
This is helpful if several devices are going to be driving similar Bose
loudspeakers, for example) with the same source signal. With EQ cards installed in the
Model 2060 or Model 2150 amplifier, the EQ OUT (output) of the amplifier can be connected
to the line level inputs of additional devices driving the same type of Bose loudspeakers
(e.g. 402 loudspeakers). Be sure to use EQ cards that correspond to the type of loudspeak-
ers.
4. Equalizer present LEDs
When you install an equalizer card, the corresponding LED illuminates to indicate the
presence of the card.
Each channel can utilize a different card. For example, the Bose Model 2150 commercial
power amplifier can have both a 402
a 502B card in either card position, it automatically selects the high frequency output of the
other card. When a system uses two or more amplifiers, and you are using a 502B module,
use the EQ BI-AMP/FULL RANGE switch to run in the bi-amp mode.
Note: When EQ cards are installed, the input module recognizes the cards and switches to
the equalizer circuitry. If no cards are installed, the input module bypasses the equalizer
circuitry and no LED will illuminate.
AM259107_00_V.pdf
9
CH 2
CH 1
SEQUENCE
REMOTE LEVEL
CH 2
CH 1
COM CH2 CH1 +5V
SND RCV
FX CH 2
FX CH 1
SEND
SEND
RECV
+
+
+
+
8
6
5
4
Equalizer Present LEDs
5
Speaker Outputs
6
Effects Loop
®
®
and a 502
B equalizer card installed. When you install
November 19, 2001
Use Class 2 Wiring
For bridged operation.
Consult user manual.
WARNING
RISK OF HAZARDOUS
ENERGY! MAKE PROPER
SPEAKER CONNECTIONS.
SEE OPERATING
INPUT IMPEDANCE 25K OHMS EACH LEG TO GROUND (TOTAL 50K OHMS BALANCED)
MANUAL BEFORE USING.
AVERTISSEMENT
ENERGIE ELECTRIQUE
DANGEREU SE. VOIR
PUSH
LANOTICE
DE FONCTIONNEMENT.
INPUT CH 2
2
1
3
J20018292
+
2
1
RECV
3
PN# 1234567
2
7
Dip Switches
8
AC Power Sequence Connector
9
Remote Level Control
10
IEC Power Cord
®
loudspeakers (402
®
4.0 Operation
SEND
RECEIVE
PUSH
INPUT CH 1
SEQUENCE
2
1
EQUALIZATION
ON
CH1
3
CH2
CH2
EQ. OUT
CH1
4
3
1
11