- ページ 8

ヒートポンプ Daikin VRVWII RWEYQ30MY1のPDF 操作マニュアルをオンラインで閲覧またはダウンロードできます。Daikin VRVWII RWEYQ30MY1 20 ページ。 Vrv-wii system air conditioner

ページを印刷する

01_EN_3P153897-1.fm Page 3 Wednesday, March 2, 2005 3:32 PM

2. WHAT TO DO BEFORE OPERA-

TION

This operation manual is for the following system

with standard control. Before initiating operation,

contact your Daikin dealer for the operation that cor-

responds to your system type and mark.

If your installation has a customized control system,

ask your Daikin dealer for the operation that corre-

sponds to your system.

Outside units (Refer to figure 1)

Cool/Heat selector

Inverter series

❏Heat pump system

❏ yes ❏ no

❏Heat recovery system

❏ yes ❏ no

• Heat pump system

• Switchover to cooling or heating operation is

performed for each outside unit.

• This is a system to perform air-conditioning by

exchanging the heat with chilled water or

warmed water being sent from a boiler or solar

system, etc. through a <outside unit> which cor-

responds to the conventional outdoor unit.

• Heat recovery system

• Switchover to cooling or heating operation is

performed for each BS unit.

• This is a system to perform air-conditioning by

exchanging the heat with chilled water or

warmed water being sent from a boiler or solar

system, etc. through a <outside unit> which cor-

responds to the conventional outdoor unit.

• Names and functions of parts (Refer to figure 1)

1. Closed cooling tower

2. Boiler

3. Outside unit

4. Indoor unit

5. BS unit (For cool/heat changeover)

3. REMOTE CONTROLLER AND

COOL/HEAT SELECTOR: NAME

AND FUNCTION OF EACH

SWITCH AND DISPLAY

(Refer to figure 2 and 3)

COOL/HEAT SELECTOR is used to switch between

cooling and heating for each outside unit or BS unit.

1. On/off button

Press the button and the system will start. Press

the button again and the system will stop.

2. Operation lamp (red)

The lamp lights up during operation.

3. Display "

It is impossible to changeover heat/cool with the

remote controller which display this icon.

4. Display "

Refer to the chapter "Operation procedure -

Adjusting the air flow direction".

5. Display "

This display shows that the total heat exchanger

unit (Heat Reclaim Ventilation) are in operation.

(these are optional accessories)

Operation modes

6. Display "

This display shows the temperature you have

set.

7. Display "

mode)

This display shows the current operation mode.

8. Display "

This display shows the programmed time of the

system start or stop.

9. Display "

When the inspection/test operation button is

pressed, the display shows the mode in which

the system actually is. (For servicing only)

10. Display "

When this display shows, the system is under

centralized control. (This is not a standard spec-

ification.)

11. Display "

This display shows the fan speed you have

selected.

12. Display "

Refer to the operation manual of indoor unit.

13. Display "

Refer to the chapter "Operation procedure -

Explanation of heating operation."

14. Timer mode start/stop button

Refer to the chapter "Operation procedure -

Programming start and stop of the system with

timer."

15. Timer on/off button

Refer to the chapter "Operation procedure -

Programming start and stop of the system with

timer."

16. Inspection/test operation button

This button is only used by qualified service

persons for maintenance purposes.

" (changeover under control)

" (air flow flap)

" (ventilation/air cleaning)

" (set temperature)

" "

" (operation

" (programmed time)

" (inspection/test operation)

TEST

" (under centralized control)

" (fan speed)

" (time to clean air filter)

" (defrost/hot start)

English