- ページ 11

スクーター Anoa EX+のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Anoa EX+ 15 ページ。 Skutis

How to use the product
Speed
8) How to control
Speed unit
the dashboard
Battery remaining
(1) Adjusting the speed mode
Change the speed mode when the dashboard is on. To display the current speed mode,
press
. The number for the speed mode will start blinking. Then press
times to set the speed (L1 – low speed, L2 – medium speed, L3 – high speed). Press
to confirm.
* Please note, that the slow start setting P7 (start mode) does not work if you selected
speed mode L1.
* When selecting the L3 speed mode (high speed), during full acceleration the speed
displayed on the dashboard may temporarily differ to the actual speed.
(2) Mode settings
Each time you press the
button
briefly, the mode changes to the next
mode.
Mode
Description
Current mileage (Press
TRIP
and hold the mode button
to set "0")
ODO
Total mileage
CHA
Not used
VOL
Current voltage(Volt)
DST
Not used
E l a p s e d t i m e , s i n c e
TIME1
dashboard was switched
on
TIME2
Not used
* Note: The voltage displayed in VOL mode
has about 1V to 2V difference from the
actual batter voltage.
20
Anoa EX / EX+ User Manual
Speed mode
Power button
Accelerator
Mode button
Speed mode
multiple
Information
(3) Returning to the main screen after setting details
Press
again to finish all settings and
return to the main screen.
(4) Detail functions
Mode
Display values and settings
P0
9 (unalterable)
P1
43.0 (unalterable)
P2
15 (unalterable)
P3
0 (fixed)
P4
Speed display: Km/h(0), mp/h (1)
Start mode: Accelerator start (0),
P5
start after kicking (1)
Cruising mode (auto riding):
P6
Off(0), on (1)
Start speed: Power start (0), slow
P7
start (1)
P8
Max. speed setting: 1 to 100%
Electric brake power: Off (0),
P9
medium (1), hard (2)
(5)
Press
P0 mode (detail function settings) > Press
P0 mode and P9 mode >Press
When changing the setting value press
setting value. > Press the
the value > Press
again to confirm all new settings.
P0
Ex) P0 default
09
value setting
(6) Features of cruise mode
The cruise control function allows you to
maintain the riding speed automatically.
This is convenient for the rider for long
distances and has the advantage of
saving battery consumption.
* Starting the cruise function
a. Select the cruise mode before riding,
as explained in section (5) above.
b. If the throttle is kept at the same
acceleration for about 7 seconds, the
cruise mode will start automatically.
* Ending the cruise function
When you hold and release the brake
while the cruise mode is running, the
cruise mode is automatically cancelled.
* Precautions when using the cruise function
Warning
For your safety, be sure to travel in a
position where the brake can be applied
immediately in order to respond to
any unforeseen incidents. in order to
respond to any unforeseen incidents.
simultaneously for about 2-3 seconds to enter the
to move between
to change setting value >
button to change the
to increase and
to decrease
simultaneously for about 2-3 seconds
(7) Adjusting the intensity of the
electric brake
The Anoa EX / EX+ is equipped with a physical
brake for the front and rear wheels, which can
be activated by pulling the physical brake lever
on the handle. Additionally, the electric brake
can be activated in the P9 detail function settings
on the dashboard. If "0" is selected, the electric
brake is off, "1" will assist with medium intensity
and "2" with strong intensity.
* The electric brake will not operate,
when the battery is fully charged
Do not use the electric brake immediately
after full charging. For your safety and to
enhance the lifetime of your battery, it
is recommended that you do not use the
electric brake with a fully charged battery.
Only use the electric brake, when more
than 5% of the battery capacity was used.
Anoa EX / EX+ User Manual
Warning
21