- ページ 6

照明器具 DRYDEN AQUA DA-GENのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。DRYDEN AQUA DA-GEN 9 ページ。
DRYDEN AQUA DA-GEN にも：ユーザーマニュアル (13 ページ)

ページを印刷する

Optional Free Chlorine control

Metering and control in ppm of

the free chlorine of the water.

Free Chlorine probe

red

black

Chlorine probe detector

FL2

(rotameter)

black

brown

blue

In case of using a Variable

Speed Pump, calibrate

the probe using the most

common filtration speed.

Optional Conductivity probe

Metering and control of

the conductivity of the

water in Msiemens.

Conductivity probe

yellow

transparent

Optional Temperature

Temperature probe

necessary to activate

the filtration modes:

Temperature

probe

heating, intelligent,

smart.

red

yellow

black

110-230 V

DRY CONTACT

max. 3.15 A

1 2 3 4 5 6

7 8 9

10 11 12 13 14

Setup and connection of a Variable Speed

Pump, see section 13 - Variable Speed Pump

4.3 MEASURES / Free Chlorine calibration

4.14

4.17

4.4 MEASURES / Conductivity calibration

4.22

4.4 MEASURES / Temperature calibration

1 2 3

5. FILTRATION / Manual mode

A1 A2

FILTER PUMP

Filtration control

4.14 Calibration of the Free Chlorine probe:

4.16

4.15

Recommended every month during usage season.

4.15 Calibration with buffer (photometer DPD1):

Follow the instructions in 6 steps that appear in the

display.

4.16 Step 1 of 6 - Calibrate Cl at 0 ppm (offset):

Close the water flow through the probe and wait until

the reading is less than 0,10 ppm. Wait between 5 to

60 min. Press OK when the reading is close to 0.

4.17 Step 3 of 6 - Calibrate Cl: Open the water

4.18

4.19

flow until achieving 80-100 liters/hour. Wait until

obtaining a stable reading of ppm. Wait between 5 to

20 min. Press OK when the reading is stable.

4.18 Step 5 of 6 - Establish the real ppm values

with the plus/minus keys according to your analysis

result of DPD1 (free chlorine).

4.19 Step 6 of 6 - If this screen is not shown repeat

the calibration process.

4.20

4.21

4.21 Manual calibration: Open de water flow and

set the flowmeter (rotameter) at the right level

of flow (80-100l/h). Wait some minutes until the

current level is stable. With the plus/minus keys,

insert manually the water chlorine level (use a

manual DPD1 test kit). Press OK when the DPD1

value is correct on display (target measurement).

4.23

4.24

4.22 Calibration of the Conductivity probe:

Recommended every month during usage season.

4.23 Calibration with buffer (buffer solution 1413 µS/

12880 µS/ neutro): Follow the instructions in 7 steps

that appear in the display (screen 4.24 corresponds

to step 1).

4.25

4.26

4.25 Manual calibration: Allows to adjust the probes

at 1 point (without buffers) – only recommended to

adjust small deviation in the readings.

4.26 Without removing the probe from the water,

use the plus/minus keys to adjust the reading so it

matches with your reference value (photometer or

other measurement).

4.27

4.28

4.28 Temperature calibration: To set difference

between the measured value of the probe and the

actual temperature, use the plus/minus and up/down

keys. Set to the actual temperature of the probe and

press OK.

5.1

5.2

5.1 Filtration:

Configuration control of the filter pump. To set, select

Filtration and confirm by pressing OK . The mode

selection is done in Mode line with the plus/minus keys.

5.2 Manual:

Manually turns ON/OFF the filtration process. No timing

or additional functions. The State line indicates whether

the filtration pump is ON.

See section Filter Cleaning below.