- ページ 3

照明器具 DS Produkte 06646のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。DS Produkte 06646 6 ページ。 Led light

ページを印刷する

■

Use suitable fastening material to hang up the article. If you

are unsure whether the fastening material supplied with the

article is suitable, seek advice from a specialist stockist.

■

Before drilling, ensure that there are no pipes or cables behind

the intended drilling point.

■

Protect the article from: impacts, heat, direct sunlight, sub-zero

temperatures, moisture and wet conditions.

■

The COB module is not replaceable.

■

Store the article in a dry place and at room temperatures.

■

Do not take the article apart and do not attempt to repair it. In

the event of any damage, please contact our customer service

department.

■

Dust off the article with a soft, dry cloth to clean it. More in-

tense soiling can be wiped off with a damp cloth.

Items Supplied

Unpack the items supplied and check them for completeness and

for possible transport damage. If you should ﬁ nd any transport

damage, do not use the article(!), but contact the customer service

department.

•

Lamp head with COB module

•

Bracket

•

3 x 1.5 V battery, AA type

•

Fastening material (2 x dowels, 2 x screws)

•

Instructions

Inserting / Changing the Battery

1. Take the lamp head out of the bracket.

2. Twist the two halves of the lamp head in

opposite directions to open the lamp head.

3. To open the battery compartment, press

the locking catch on the battery compart-

ment cover and remove it.

4. Take used batteries out if necessary and

insert 3 new 1.5 V batteries of the AA type.

Pay attention to the correct polarity (+ / –)

(see inside of battery compartment).

5. Insert the battery compartment cover and

ﬂ ip it shut so that you hear and feel it en-

gage in place.

6. Put the two halves of the lamp head back

together and twist them tight.

If the performance of the article diminishes or it starts to ﬂ icker, the

batteries should be replaced.

Wall Mounting

The motion sensor only works in a dark environment.

You should therefore only afﬁ x it in places with low

light absorption!

If the light is to be attached to the wall, the bracket (recess for nail

or screw present on the bottom) must be screwed onto the wall.

Use the fastening material supplied to attach the bracket. The type

of fastening material will depend on the condition of the wall on

which the light is to be attached. Make sure you follow the safety

instructions for assembly.

Use

1. Switching on – Twist the two halves of the lamp head in oppo-

site directions to open the lamp head. Slide the On / Off switch

to the position you want.

AUTO: The light switches on automatically when the motion

sensor registers a movement. The light switches off again after

around 25 seconds without registering a movement.

ON: The light is permanently switched on.

DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •

*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.

Artikelnummer: 06646

Put the two halves of the lamp head back together and twist

them tight.

2. Setting the illumination angle – The lamp head can be piv-

oted 360°, for individual alignment. Carefully insert it into the

bracket and adjust it to the position you want.

3. Positioning the article – The article can be set up or posi-

tioned on walls using suitable fastening material.

4. Switching off – If the light is no longer to be used, twist the

two halves of the lamp head in opposite directions to open the

lamp head. Slide the On / Off switch to the OFF position.

Technical Data

Article number:

Model number:

Voltage supply:

Power:

Lighting time:

Nominal luminous ﬂ ux:

Motion sensor:

– Coverage angle:

– Range:

Protection class:

Disposal

Dispose of the packaging material in an environmentally

friendly manner and take it to a recycling centre.

Dispose of the article in an environmentally friendly man-

ner at a recycling centre for used electrical and electronic

devices. It should not be disposed of in the normal house-

hold waste. More information is available from your local

authorities.

The batteries should be removed prior to disposal of the

article and disposed of separately. To protect the environ-

ment, non-rechargeable and rechargeable batteries must

not be disposed of with normal household waste, but must

be taken to suitable collection points. Also note the relevant

statutory regulations governing the disposal of batteries.

Customer Service / Importer:

06646

XGCL-08MC

4.5 V DC (3 x 1.5 V batteries, AA type)

1 W

approx. 25 s

approx. 120 lm

approx. 120°

approx. 5 m

III

✆

+49 38851 314650 *)

Z 06646 M DS V1 1117

Instructions