- ページ 3

ホーム照明アクセサリー DS Produkte 06815のPDF マニュアルをオンラインで閲覧またはダウンロードできます。DS Produkte 06815 6 ページ。

ページを印刷する

■

Do not make any changes to the articles and do not attempt

to repair them. In the event of any damage, please contact our

customer service department. The individual LEDs cannot be

replaced.

■

Under no circumstances should you use any corrosive or abra-

sive cleaning agents, rough sponges or knives to clean the

article. These could damage the surfaces.

Items Supplied

Check the items supplied for completeness and possible transport

damage. If you should ﬁ nd any transport damage, do not (!) use

the articles, but contact the customer service department.

•

LED light with motion sensor and adhesive pads (2 x)

•

Fastening material (4 x dowels, 4 x screws)

•

Instructions (1 x)

In addition, 3 batteries (1.5 V, AAA type) are required in each case.

These are not supplied with the articles.

Inserting / Changing Batteries

Before inserting the batteries, check whether the contacts are

clean and clean them if necessary.

Always replace all batteries together. Do not use batter-

ies of different types or brands, or batteries with different

capacities.

1. Slide the battery compartment cover in the direction of the

LEDs and remove it.

2. Take out used batteries if necessary and insert three batteries

(1.5 V, AAA type) into the battery compartment. Ensure the

correct polarity (+ / –).

3. Insert the battery compartment cover into the rails and slide

it shut.

Replace the batteries when the power of the lights starts to wane.

Use

1. Positioning the articles – The articles can either be attached

to the wall using the fastening material supplied or be afﬁ xed to

smooth surfaces using the adhesive pad on the back.

Mounting with fastening material:

– Remove the battery compartment cover.

– Place the battery compartment cover on the wall and mark

out two drill holes.

– Drill holes into the wall and place dowels in them.

– Screw the battery compartment cover onto the wall.

– Slide the light onto the battery compartment cover.

Mounting with adhesive pad:

– Thoroughly clean the location you want. It must be smooth,

dry, and free of any dust, grease or dirt.

– Peel off the protective ﬁ lm from the adhesive pads on the

back of the articles and afﬁ x the articles.

2. Switching on – Slide the On / Off switch to the ON position.

The lights switch on automatically when the motion sensors

30 seconds without registering a movement.

3. Switching off – If the lights are no longer to be used, slide the

On / Off switch to the OFF position.

Cleaning

1. Take the batteries out of the articles.

2. Clean the articles with a soft, damp cloth and a little mild

detergent if necessary.

3. Thoroughly dry off the articles before they are stored away.

DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •

*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.

Article number: 06815

Technical Data

Article number:

Model number:

Power supply:

Power:

Lighting time:

Nominal luminous ﬂ ux:

Illuminance:

Motion sensor:

– Coverage angle:

– Range:

Protection class:

ID of instructions:

Disposal

Dispose of the packaging material in an environmentally

friendly manner so that it can be recycled.

These articles are governed by the European Directive

2012/19/EU on waste electrical and electronic equipment

(WEEE). Do not dispose of these articles as normal domes-

tic waste, but rather in an environmentally friendly manner

via an ofﬁ cially approved waste disposal company.

Batteries should be removed before the articles are dis-

posed of and should be disposed of separately from the

articles at suitable collection points.

Customer Service / Importer:

06815

TFJO18002

4.5 V DC (3 x 1.5 V battery, AAA type)

approx. 1 W

approx. 30 s

approx. 32 lm

5 lux

approx. 120°

approx. 3 m

III

Z 06815 M DS V1 1018

✆

+49 38851 314650 *)

Instructions