- ページ 7

屋外ライト Daintree GE Current Lumination Tetra Contour 75487 SeriesのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Daintree GE Current Lumination Tetra Contour 75487 Series 7 ページ。

ページを印刷する

Lumination

(Tetra

Troubleshooting

Symptom

No AC input

All LEDs are OFF

Incorrect wire attachment

Overload (maximum load

exceeded)

Some LEDs

Maximum recommended supply

appear dim

wire length exceeded

Mixed Suffix Codes of LED light

engine within an application

Some of the sections

Incorrect wire attachment

are not illuminated

Light/dark banding

LED light engine stretched

along a section

during installation

Loading Chart

LED Driver

79045 (GE080/MV/D24T1-A)

67825 (GEPS24-100UGL-IP)

62189 (GE180/MV/V24T1-C)

Remote Mounting Distance

LED Driver

79045 (GE080/MV/D24T1-A)

67825 (GEPS24-100UGL-IP)

62189 (GE180/MV/V24T1-C)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-005 (A) / NMB-005 (A)

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Contour - Series)

Condition

Attach AC input and/or check circuit breaker

Check wire connection(s) at the Tetra Contour LED light engine and power supply for im-

proper connections or short circuits. Make sure you have positive to positive and negative

to negative wire connections.

Ensure the overall length of Tetra Contour LED light engine does not exceed the maximum

load as detailed in the Tetra

Reduce the length of supply wire equal to or below the recommended maximum.

Make sure that all LED light engines have the same Suffix Code

(Suffix Code is located on each packaging label).

Check the wire connections at the Tetra Contour LED light engine for improper connec-

tions. Make sure you have positive to positive and negative to negative wire connections.

Check for improper cutting resolution locations (see Item 21 on Page 2).

Remove LED light engine and properly install.

Inspect and replace light engine if the silicone is damaged.

Minimum Loading

8 in. (0.20m)

18 AWG (0.82mm

Supply Wire

1-20 ft. (0.3-6.1m)

www.gecurrent.com

General Electric Company and are used under license. Information provided is subject to change without

notice. All values are design or typical values when measured under laboratory conditions.

ARCH018 (Rev 04/02/2021)

Power Supply Installation Instructions.

Maximum Loading

White Colors

22 ft. (6.69m)

27 ft. (8.19m)

25 ft. (7.59m) per Bank/

50 ft. (15.18m) per Driver

)

16 AWG (1.31mm

)

14 AWG (2.08mm

Supply Wire

30 ft. (0.3-9.1m)

Installation Guide

Solution

Maximum Loading

RGB Colors

50 ft. (15.24m)

59 ft. (17.98m)

55 ft. (16.76m) per Bank/

110 ft. (33.53m) per Driver

)

12 AWG (3.31mm

Supply Wire

50 ft. (0.3-15.2m)

86 ft. (0.3-26.1m)

)