- ページ 8
セキュリティシステム DSC PC 5010のPDF クイックマニュアルをオンラインで閲覧またはダウンロードできます。DSC PC 5010 20 ページ。
DSC PC 5010 にも： 取扱説明書 (10 ページ)
ページを印刷する
PC5508, PC5516 and PC5532 Keypads:
Press the keys on the number pad to view alarms or troubles, to
Arm/Disarm the system or to bypass zones.
To exit, press [#]; to select a function, press [ ].
PC5508 LED Keypad
PC5516 LED Keypad
PC5516 LED Keypad
The PC5508 and PC5516
Keypads are available for
applications with fewer than
32 zones. The functions
explained in this manual are
the same for all three LED
keypad types.
Display Lights
Ready Light
:
Armed Light
(All keypads)
If the Armed light is ON, the system has
If the Ready light is ON, the system is
been armed successfully.
ready for arming.
If the Ready light is OFF, check to see
Trouble Light
that all doors and windows are closed
If the Trouble light is ON, check to see
and that all movement is stopped in
what the trouble condition is and call
areas covered by motion detectors.
for service (See "Viewing Trouble
The system cannot be armed unless
Conditions" on page 12).
the Ready light is ON indicating that all
zones are closed and the system is in
the Ready state.
8
PC5532 LED Keypad
:
Memory Light
(All keypads)
(LED keypads only)
Upon disarming, if an alarm has
occurred while the system was armed,
the Memory light will turn ON (See
:
(All keypads)
"Disarming the System" on page 6).
Bypass Light
(LED keypads only)
If the Bypass light is ON, ensure that
zones are intentionally bypassed
before arming the system (See "Zone
Bypassing" on page 11).
All Keypads:
Function Keys
(Stay, Away, Chime, Reset, Exit):
If activated by your installer, these
keys allow easy single button
activation of the most commonly used
features. For more information, talk to
your alarm installer.
Press both
Keys for two seconds
to send a FIRE transmission.
Press both
Keys for two seconds
to send an AUXILIARY transmission.
Press both
Keys for two seconds
to send a PANIC transmission.
NOTE
(All Keypads)
: The Fire,
Auxiliary and Panic keys will NOT
function unless programmed by
the installer. If these keys are in
service and the installer has enabled
audible feedback, holding down the
key for two seconds will cause the
keypad sounder to beep indicating
that the input has been accepted and
transmission is underway.
:
Fire Light
:
(LED keypads only)
If the Fire light is ON, a fire alarm has
occurred (See "Fire Alarm Operation"
on page 14).
Program Light
:
(LED keypads only)
:
The Program light will flash you are
programming access codes, setting
the system time or performing other
programming functions. If someone is
programming at another keypad, the
Program light will turn ON to indicate
that the system is busy.
LCD5500 Keypad
LCD5500 Keypad:
The Liquid Crystal Display (LCD) displays prompts and
system information on two 16 character lines.
If "< >" appears, more information can be accessed by
using the arrow (< >) keys. Press [<] to see the previous
function or item of information. Press [>] to advance the
display to next function or item of information.
Press the keys on the number pad as prompted by the
LCD display to view alarms or troubles, to arm and
disarm the system and to bypass zones.
To exit a function and return to the Ready state, press [#];
to select a function press [ ].
NOTE: All functions can be performed from any LCD
keypad by using the LED keypad commands, as well
as by scrolling through the message display.
Important Note: Test system weekly and have any system
trouble conditions corrected by your alarm installer.
9