- ページ 7

セキュリティシステム DAITEM SH401AXのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。DAITEM SH401AX 9 ページ。 Indoor siren

ページを印刷する

7. Maintenance

7.1 Fault indications

The control panel supervises and identiﬁes the siren.

It monitors the state of the:

• power supply,

• radio link,

• tamper contact.

If a fault is memorised the control panel issues a voice message to indicate the fault following a system command

(see § Fault indications in the control panel installation manual).

7.2 Changing the battery

• The lithium battery pack must be replaced by the same type of pack with the same technical characteristics,

i.e. 2 x (3.6 V – 13 Ah).

• We advise you to use the DAITEM BatLi22 pack available in the catalogue in order to guarantee individual safety

and equipment reliability.

• Dispose of the waste lithium power pack in an appropriate recycling bin.

To change the battery:

1. send a disarm command,

2. switch the control panel to installation mode:

master code

3. remove the siren from the wall,

4. remove the faulty lithium power pack,

5. wait for 2 minutes before connecting the new lithium pack,

6. close the siren and put it back on its base,

7. switch the control panel to user mode:

installer code

8. test triggering.

8. Summary of parameters

Parameter description

Delayed sounding

upon intrusion

Sounding duration

Sound level of disarm/arm

indications

Transfer of disarm/arm

indications

Indication of audible signals

and door bell

Validation of radio link

in installation mode

Triggering upon intrusion

Protection system armed

indication

Alarm indication in armed

presence mode

Triggering upon

communication network

interruption

Radio tamper

Allocation of a siren to one

or several intrusion groups

Deletion of all parameters

Deletion of one parameter

then

installer code

Parameter-setting sequence

** 4 * siren n° * 3 * ?? **

** 4 * siren n° * 4 * ??? **

** 4 * siren n° * 11 * ? **

** 4 * siren n° * 12 * ? **

** 4 * siren n° * 13 * ? **

** 4 * siren n° * 15 * ? **

** 4 * siren n° * 20 * ? **

** 4 * siren n° * 21 * ? **

** 4 * siren n° * 22 * ? **

** 4 * siren n° * 26 * ? **

** 4 * siren n° * 27 * ? **

** 4 * siren n° * 37 * ? **

** 4 * siren n° * 197 ***

** 4 * siren n° * parameter n° ** 0 **

Factory

parameter

0: immediate

from 0 to 60 s

0: immediate

90 s

from 20 s to 180 s

4: average

from 1 to 8

1: sound

0: disabled

1: sounding

1: enabled

0: disabled

1: enabled

0: on one

0: validation on 1 of 2 bands

of 2 bands

1: validation on 2 bands

1: single

0: disabled

or conﬁrmed

1: single or conﬁrmed intrusion

intrusion

2: conﬁrmed intrusion only

1: audible

0: disabled

1: sounding

2: loud sounding

0: disabled

(15 s)

1: quiet sounding (4 beeps)

2: loud sounding (15 s)

0: disabled

1: loud sounding triggered if the system

is totally armed

2: loud sounding triggered 24/24

1: enabled

0: disabled

1: enabled

all groups

Selection of group(s): from 1 to 8

depending on type of control panel

Possible values

Page