- ページ 9

コントロールパネル DSC Power632のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。DSC Power632 11 ページ。 Power632
DSC Power632 にも：取扱説明書 (11 ページ)

ページを印刷する

Continued from page 7 ...

Programming codes from an LCD Keypad:

Master Code

Press the [ ] key to enter the function list. Scroll (< >) to...

Press (*) for <>

Press [5] or [ ]. The display will read...

Access Codes

Enter Master

Enter your current Master Code. The display will read...

Access Code

(*) to Edit

"40P" represents the Master Code. Press the [ ] key to indicate that you wish to

User Code

40P

program the Master Code. The display will read...

Enter New Code

Enter the new Master Code. The Master Code must be four digits long, unless

1234

otherwise indicated by your installer. Enter digits 0 through 9 only. Once the new

code is entered, the keypad will beep 3 times and the display will read...

(*) to Edit

Press [#] to exit the code programming function.

User Code

40P

Be sure to record your new Master Code on the "System Information" page in this booklet.

NOTE: We recommend that the factory default Master Code [1234] not be used.

Additional Access Codes

To erase, add or change a user code, press [ ] to enter the function list. Use the arrow (< >) keys to

scroll to the following message...

Press [ ]. Display will read...

Press (*) for <>

Access Codes

Enter the Master Code. Display will read...

Enter Master

Access Code

[*] to Edit

Use the scroll keys (< >) to find the access code – indicated by "02P" to "32P" –

User Code

01P

you wish to add, change or delete. Press the [ ] key to select the code you wish to

change. The display will read...

To add or change a code, enter the new code. Access codes must be four digits

Enter New Code

1234

unless otherwise indicated by your installer. Enter digits 0 through 9 only. To delete

an access code, enter [ ]. Once the 4-digit code or [ ] has been entered, the

keypad sounder will beep 3 times and the display will read...

The "P" means the code has been programmed. If there is no "P" then that code is

[*] to Edit

User Code

01P

deleted. Press [#] to exit the code programming function. The Master code cannot be

erased.

Remember to record your new code(s) on the "System Information" page in this booklet.

Access Code Attributes

Additional programmable attributes, such as zone bypassing capability, can be activated or deactivated

for each access code. For more information regarding access code attributes, please contact your

installer.

If an Alarm Sounds

Fire Alarm

If your system has been installed with fire detectors and the alarm sounds in a pulsing mode, follow

your emergency evacuation plan immediately (see "Fire Escape Planning" on page 15).

Intrusion Alarm

If an intrusion alarm sounds, indicated by a continuous Bell or Siren, the alarm may be silenced by

entering your access code. If the alarm was unintentional, call local authorities immediately to avoid an

unnecessary response.

You can determine the source of the alarm by following the instructions in the "Disarming" section (see

page 6). Once the source of the alarm has been corrected, the panel can be restored to its original

Armed state.

NOTE: A fire alarm has priority over a burglary type alarm.

Function Keys

(Not available on the PC1555RKZ)

The keypads have five function keys – marked Stay, Away, Chime, Reset and Exit – which allow easy

single-button activation of the most commonly used features. If your installer has enabled these keys, you can

execute their programmed function by pressing and holding the corresponding key for two seconds.

For information regarding the operation of the function keys, talk to your alarm installer.

Programming Security Codes

Programming codes from an LED or Fixed Message LCD5501Z keypad:

The Master Code

To program the Master Code, enter [ ][5][current Master Code][40][new Master Code]. The Master

Code must be four digits long, unless otherwise indicated by your installer. Enter digits 0 through 9

only. Press [#] to return to the Ready state.

NOTE: You must program all digits in each access code.

Be sure to record your new Master Code on the "System Information" page in this booklet. NOTE: We

recommend that the factory default or obvious codes such as [1111] or [1234] not be used.

Additional Codes

Up to 32 additional access codes (01 through 32) may be programmed.

To program a new code:

Enter [ ][5][Master Code][code number 01 to 32][new access code]. The code number is a double

digit from 01 to 32. Access codes must be four digits unless otherwise indicated by your installer.

Enter digits 0 through 9 only. Press [#] to return to the Ready state.

If an access code already exists for the code number you have selected, it will be replaced by the new

code. Be sure to record your new code(s) on the "System Information" page in this book.

To erase a code:

Enter [ ][5][Master Code][code number 01 to 32][ ]. Press [#] to return to the Ready state. The

Master code cannot be erased.

Continued on page 10 ...