- ページ 2

コントロールユニット DSC Maxsys PC4701のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。DSC Maxsys PC4701 2 ページ。 Fire expansion module

ページを印刷する

For more information regarding module enrollment, see the

control panel Installation Manual.

Programming the Module

To access PC4010/PC4020 programming, enter [*][8] followed

by the Installer's code. Program the sections indicated on this

worksheet, and record your programming choices in the space

provided. The waterflow and 2-wire smoke zones are hard-coded

and the zone type cannot be changed. Refer to your Commercial

Fire Installation Guide for more information on PC4701 zones.

If the 2-wire smoke auto-verify feature is enabled in the System

Toggles section (ref. # [000200]), the panel will automatically

verify alarms from the 2-wire smoke circuit of the PC4701 before

Please refer to your PC4010/PC4020 Installation Manual for information on how to program.

Event Messages

[0001]

[000102]

2-Wire Smoke

[000103]

Waterflow

System Toggle Options: scroll to 2WS AutoVerify

[000200]

[00020311]

Waterflow Delay

NOTE: If a waterflow delay is programmed, the PC4701 waterflow zone follows it. Please see your PC4010CF/4020CF Installation

Guide for more details.

[000403]

Reporting Codes

[00040309]

Fire Events

2 Wire Alarm

2 Wire Restore

Waterflow Alarm

Waterflow Rest.

INDUSTRY CANADA NOTICE

NOTICE: The Industry Canada label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective, operational

and safety requirements. Industry Canada does not guarantee the equipment will operate to

the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected

to the facilities of the local telecommunications company. The equipment must also be

installed using an acceptable method of connection. The customer should be aware that

compliance with the above conditions may not prevent degradation of service in some

situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance

facility designated by the supplier. Any repairs or alterations made by the user to this

equipment, or equipment malfunctions, may give the telecommunications company cause

to request the user to disconnect the equipment.

User should ensure for their own protection that the electrical ground connections of the

power utility, telephone lines and internal metallic water pipe system, if present, are

connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves, but should

contact the appropriate electric inspection authority, or electrician, as appropriate.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device

provides an indication of the maximum number of terminals allowed to be connected to

a telephone interface. The termination on an interface may consist of any combination of

devices subject only to the requirement that the sum of the Ringer Equivalence Number

of all the devices does not exceed 5.

The REN of this unit is 0.0.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security

Controls Ltd. could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

Re-orient the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: "How to Identify

and Resolve Radio/Television Interference Problems". This booklet is available from

the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-

00345-4.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules. On the side of this

equipment is a label that contains, among other information, the FCC registration

number of this equipment.

NOTIFICATION TO TELEPHONE COMPANY The customer shall notify the

telephone company of the particular line to which the connection will be made,

and provide the FCC registration number and the ringer equivalence of the

protective circuit.

FCC Registration Number:

Ringer Equivalence Number:

USOC Jack:

TELEPHONE CONNECTION REQUIREMENTS Except for the telephone company

provided ringers, all connections to the telephone network shall be made through

1645 Flint Road, Downsview, Ontario, Canada M3J 2J6

Security Products

(416) 665-8460 • Fax (416) 665-7498 • 1-800-387-3630

I______I______I______I______I______I______I______I______I______I______I______I______I______I______I______I______I

Default: 000

I ______ I ______ I

F53CAN-32904-AL-N

0.0B

RJ31X

sounding the bells and transmitting the alarms.

Verification will function as follows: when the 2-wire smoke

circuit is shorted, the PC4701 performs a sensor reset by removing

power from the circuit for 20 seconds. After the 20 second reset,

power will be restored to the circuit and troubles will be bypassed

for 10 seconds to allow detectors to settle. If the smoke detectors

inititate another alarm within 60 seconds after power is restored,

a fire alarm will be generated immediately. If the smoke detector

is not reset by the power down, the zone will not be restored. If

this occurs, the panel will initiate a fiire alarm immediately (30

seconds after initial alarm).

If the feature is disabled, the panel will generate fire alarms

instantly.

Default: N

Valid entries are 000-090 seconds.

I______I______I______I

2 Wire Trouble

I ______ I _ _____ I

2 Wire TBL Rest.

I ______ I _ _____ I

Waterflow TBL

I ______ I _ _____ I

Waterflw TBL Rest

I ______ I _ _____ I

AVIS: L'étiquette de l'Industrie Canada identifie le matériel homologué. Cette étiquette

certifie que le matériel est conforme à certaines normes de protection, d'exploitation et de

sécurité des réseaux de télécommunications. Industrie Canada n'assure toutefois pas que

le matériel fonctionnera à la satisfaction de l'utilisateur.

Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux

installations de l'entreprise locale de télécommunication. Le matériel doit également être

installé en suivant une méthode acceptée de raccordement. L'abonné ne doit pas oublier

qu'il est possible que la conformité aux conditions énoncées ci-dessus n'empêchent pas la

dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être effectuées par un centre d'entretien

canadien autorisé désigné par le fournisseur. La compagnie de télécommunications peut

demander à l'utilisateur de débrancher un appareil à la suite de réparations ou de

modifications effectuées par l'utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de

la source d'énergie électrique, les lignes téléphoniques et les canalisations d'eau métalliques,

s'il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans

les régions rurales.

AVERTISSEMENT: L'utilisateur ne doit pas tenter de faire ces raccordements lui-

même; il doit avoir recours à un service d'inspection des installations électriques, ou à

un électricien, selon le cas.

AVIS: L'indice d'équivalence de la sonnerie (IES) assigné à chaque dispositif terminal

indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La

terminaison d'une interface téléphonique peut consister en une combinaison de quelques

dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de

tous les dispositifs n'excède pas 5.

L'indice d'équivalence de la sonnerie (IES) de ce produit est 0.0.

standard plugs and telephone company provided jacks, or equivalent, in such a

manner as to allow for easy, immediate disconnection of the terminal equipment.

Standard jacks shall be so arranged that, if the plug connected thereto is withdrawn,

no interference to the operation of the equipment at the customer's premises which

remains connected to the telephone network shall occur by reason of such withdrawal.

INCIDENCE OF HARM Should terminal equipment or protective circuitry cause

harm to the telephone network, the telephone company shall, where practicable,

notify the customer that temporary disconnection of service may be required;

however, where prior notice is not practicable, the telephone company may temporarily

discontinue service if such action is deemed reasonable in the circumstances. In the

case of such temporary discontinuance, the telephone company shall promptly

notify the customer and will be given the opportunity to correct the situation.

ADDITIONAL TELEPHONE COMPANY INFORMATION The security control panel

must be properly connected to the telephone line with a USOC RJ-31X telephone

jack.

The FCC prohibits customer-provided terminal equipment be connected to party

lines or to be used in conjunction with coin telephone service. Interconnect rules may

vary from state to state.

CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The

telephone company may make changes in its communications facilities, equipment,

operations or procedures, where such actions are reasonably required and proper

in its business. Should any such changes render the customer's terminal equipment

incompatible with the telephone company facilities the customer shall be given

adequate notice to the effect modifications to maintain uninterrupted service.

RINGER EQUIVALENCE NUMBER (REN) The REN is useful to determine the

quantity of devices that you may connect to your telephone line and still have all of

those devices ring when your telephone number is called. In most, but not all areas,

the sum of the RENs of all devices connected to one line should not exceed five (5.0).

To be certain of the number of devices that you may connect to your line, you may

want to contact your local telephone company.

EQUIPMENT MAINTENANCE FACILITY If you experience trouble with this telephone

equipment, please contact the facility indicated below for information on obtaining

service or repairs. The telephone company may ask that you disconnect this

equipment from the network until the problem has been corrected or until you are

sure that the equipment is not malfunctioning.

Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094

I _ _______I

Fire Test Begin

I _ _____ I ______ I

Fire Test End

I _ _____ I ______ I

Fire Bypass

I _ _____ I ______ I

Fire Unbypass

I _ _____ I ______ I

Printed in Canada 29002894 R1