- ページ 2

煙警報器 DSC FSA-210BRのPDF 設置および操作説明書をオンラインで閲覧またはダウンロードできます。DSC FSA-210BR 4 ページ。 Fsa-210 series smoke detector

ページを印刷する

Install Smoke detectors in accordance with NFPA 72, Ch. 11.

"Smoke detectors shall be installed outside of each sleeping area in

the immediate vicinity of the bedrooms and on each additional story

of the family living unit, including basements and excluding crawl

spaces and unfinished attics. In new construction, a smoke detector

also shall be installed in each sleeping room."

2. Mount Smoke Detector Backplate

Mount backplate on standard 4" octag-

Locking

onal electrical box using the screws pro-

Tab

vided.

NOTE: Power supply must be supplied

from a UL Listed alarm control unit. Install

wiring in accordance with the appropri-

ate national and local electrical codes.

CAUTION: The dust cover protects the

unit when not in service. Remove dust

Mounting Holes

cover before use.

3. Wiring

Refer to the wiring diagrams in this installation sheet and those

provided in the Installation Manual of the alarm control panel

being used with the unit. Before connecting the unit, prepare the

wires from the electrical box for connection; Do not use frayed or

bent wire.

9.35-30VDC

V+

+ + -

NOTE: Optional Remote LED

must have a series resistor.

Please see specifications.

LED

Relay

NO NC C

OPTIONAL

CAUTION: Do NOT use looped wire under terminals. Break the

wire run, to provide supervision of connections

When wiring is completed, inspect the wiring and correct any

errors before applying power to the unit. When the wiring has

been thoroughly reviewed, neatly insert the wires into the electri-

cal box and secure the unit to the mounting plate.

4. Mounting

Detector Installation:

Position the detector on to the

base plate using the detector and

base plate alignment marks. Press

the detector gently in place while

rotating the detector clockwise

until the detector snaps into

place. Remove the side tab from

the locking tab to lock in place

(optional).

Removal: If the side tab is removed to lock the detector, depress

tab with a small flat blade screwdriver and rotate detector

counter-clockwise until the alignment marks line up. Remove

detector.

EOL Device

+ + -

Tab

Alignment

Open

Marks

5. Test Unit

Initiate test for units without a sounder by placing a magnet near

the LED/Test Button for greater than 5 seconds. Initiate test for

units with a sounder by pressing the test button for greater than

5 seconds.

Alarm activation is indicated by the LED, the sounder, and the

alarm reporting to the Control Panel. If the smoke detectors are

inter-connected using model PRM-2W and a detector is tested,

then all detectors will sound. The detector restores to normal

when the test button is released or when the magnet is removed.

NOTE: Allow a minimum of 20 seconds between test activations.

NOTE: If the detector is in one of the following states when a test

is initiated; it will not enter an alarm state.

Compensation trouble.

Failure of heat or smoke detector.

Other internal faults that could prevent a smoke or heat

alarm.

NOTE: Smoke sensitivity of installed detectors can be measured

without removal or an alarm being generated using the FSD-100

Smoke Detector Test Meter.

Test Unit with FSD-100 Smoke Detector Test Meter

To test the unit using the FSD-100, set the test meter up to read

devices as per the instructions supplied with the test instrument.

Depress the test button (or place the FSD-100 on the outside

edge of the plastics beside the test button to activate the reed

switch on units without sounder) on the smoke detector for 1

second and release.

NOTE: If the test button is held for 5 seconds or longer, an alarm

will be generated.

Move the test meter over the center of the detector, wait until

you hear the test meter beep, remove the unit and the informa-

tion can be immediately reviewed. Please see the instructions sup-

plied with the FSD-100 Smoke Detector Test Meter for more

information.

NOTE: Perform the tests one at a time. Performing simultaneous

tests on multiple detectors may trigger an alarm at the control

panel.

6. Compensation Reset

Cleaning, replacement of the smoke sensor, or other changes

may change the background signal/noise of the detector; this

requires the drift compensation be reset. Compensation trouble is

one of the faults indicated when the LED indicator is OFF while

the sounder is chirping.

Remove power from the unit, then press and hold the test but-

ton for 30 seconds to power down unit.

Power up unit while pressing the test button.The LED will

flash; when 5 seconds has elapsed. Release the test button

within 1 second after the fifth LED flash.

The LED will flash every 8 seconds for 1 minute. When the

detector stops flashing test the detector to verify normal

operation.