- ページ 2

煙警報器 DSC FSA-410 SeriesのPDF 設置および操作説明書をオンラインで閲覧またはダウンロードできます。DSC FSA-410 Series 4 ページ。

ページを印刷する

Install smoke detectors in accordance with NFPA 72,

Chapter 11: "Smoke detectors shall be installed outside of

each sleeping area in the immediate vicinity of the bedrooms

and on each additional story of the family living unit, including

basements and excluding crawl spaces and unfinished attics.

In new construction, a smoke detector shall also be installed in

each sleeping room."

2. Mount Smoke Detector Backplate

Mount backplate using screws

provided and the appropriate holes

on the mounting plate.

NOTE:

Install wiring in accor-

dance

with

the

appropriate

national and local electrical codes.

For UL/ULC Installations, the power

supply must be supplied from a

UL/ULC Listed alarm control unit.

CAUTION: The dust cover pro-

tects the unit when not in service.

Remove dust cover before use.

3. Wiring

Refer to the wiring diagrams in this installation sheet and

those provided in the Installation Manual of the alarm control

panel being used with the unit. Before connecting the unit,

prepare the wires from the electrical box for connection; Do

not use frayed or bent wire.

10-30V

To alarm

initiating

circuit

NO C

Alarm Relay

LED

Aux Relay

NO NC C

OPTIONAL

CAUTION: Do NOT use looped wire under terminals for sys-

tem supervision. Break the wire run, to provide supervision of

connections.

When wiring is completed, inspect it and correct any errors

before applying power to the unit. When the wiring has been

thoroughly reviewed, neatly insert the wires into the electrical

box and secure the unit to the mounting plate.

To connect this device use only wiring listed as fit for the pur-

pose.

4. Mounting

Detector Installation

Position the detector on to the base plate using the detector

and base plate alignment marks. Press the detector gently in

place while rotating the detector clockwise until the detector

Locking

Tab

Mounting Holes

NOTE:

Optional remote LED must have

a series resistor. Please see

specifications.

snaps into place. Remove the side tab from the locking tab to

lock in place (optional).

Removal: If the side tab is removed to

lock the detector, depress tab with a

small flat blade screwdriver and rotate

detector counter-clockwise until the

alignment marks line up. Remove

detector.

5. Test Unit

Initiate test for units without a siren by

placing a magnet near the LED/Test Button for greater than 5

seconds. Initiate test for units with a siren by pressing the test

button for greater than 5 seconds.

Alarm activation is indicated by the LED, the siren, and the

alarm reporting to the control panel. If the smoke detectors

are inter-connected using model PRM-4W and a detector is

tested, then all detectors will sound. The detector restores to

normal when the test button is released or when the magnet

is removed.

NOTE: Allow a minimum of 20 seconds between test activa-

tions.

NOTE: If the detector is in one of the following states when a

test is initiated; it will not enter an alarm state.

1. Compensation trouble.

2. Failure of heat or smoke detector.

3. Other internal faults that could prevent a smoke or heat

alarm.

NOTE: Smoke sensitivity of installed detectors can be mea-

sured without removal or an alarm being generated using the

FSD-100 Smoke Detector Test Meter.

RM-2

Test Unit with FSD-100 Smoke Detector Test Meter

NO C NC

To test the unit using the FSD-100, set the test meter up to

read devices as per the instructions supplied with the test

instrument. Depress the test button (or place the FSD-100 on

Panel

the outside edge of the plastics beside the test button to acti-

EOLR

vate the reed switch on units without siren) on the smoke

detector for 1 second and release.

NOTE: If the test button is held for 5 seconds or longer, an

alarm will be generated. Move the test meter over the center

of the detector, wait until you hear the test meter beep,

remove the unit and the information can be immediately

reviewed. Please see the instructions supplied with the FSD-

100 Smoke Detector Test Meter for more information.

6. Compensation Reset

Cleaning, replacement of the smoke sensor, or other changes

may change the background signal/noise of the detector; this

requires the drift compensation be reset. Compensation trou-

ble is one of the faults indicated when the LED indicator is OFF

while the siren is chirping.

• Remove power from the unit, then press and hold the test

button for 30 seconds to power down unit.

• Power up unit while pressing the test button.The LED will

flash; when 5 seconds has elapsed. Release the test button

within 1 second after the fifth LED flash.

• The LED will flash every 8 seconds for 1 minute. When the

detector stops flashing test the detector to verify normal

operation.

Mounting

Surface

Backplate

Alignment

Tabs

Marks

Detector

OPEN