トレッドミル Attacus AT-500のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Attacus AT-500 3 ページ。
ページを印刷する
AT500 Specifica on
Basic specifica on
Unit dimensions:
Length: 188 CM (74.02 in)
Width: 89 CM (35.04 in)
Height: 135 CM (53.15 in)
Unit weight:
113.5 KG (250.2 lb)
Maximum weight
130 KG (287 lb)
carrying capacity:
Belt size:
51 x 140 CM (20 x 55 in)
Motor:
1.75 HP
Voltage:
110V
220V，50/60Hz
Speed:
0.8~18 (KM/HR)
Incline:
10 %
Basic equipment
Hand held heart
YES
rate monitor:
Wireless receiving
5 kHz, Bluetooth and ANT+
device:
Fan:
YES
Audio:
Bluetooth audio device/High
quality audio
Fan
Magazine rack
Rack
Quick key panel
Power switch/power cord
Upright
Upright safety cover
Hydraulic li system
Non-skid mat
Troubleshoo ng of The Heart Rate
Wearable connec on
Please correctly wear the heart rate monitor(op onal accessories) according following steps. The posi on and ghtness will influence the accuracy of
detec on:
1) Adjust the strap length to fit ghtly but comfortably around your chest and avoid any slide during workout.
2) Make sure the fastener of heart rate monitor sensor is securely fastened.
3) Wet the electronic sensing area with clean water.
4) Wear your monitor under your chest.
5) Make sure the monitor is worn in right direc on. The logo must be at exact center of your chest to ensure successful and accurate detec on.
Troubleshoo ng
Fluorescent lamps, computers or large motors may interfere the detec on and lead to inaccurate heart rate reading:
1)Your heart rate reading may be unstable under following condi ons:
•The holds to heart rate sensor bar are too ght. Please hold the heart rate sensor bar with appropriate stress.
•Mo on and vibra on caused by con nuous hold to the heart rate sensor bar during the workout.
•Users with heavy breathing during the workout or thick skin on the palms.
•Wearing accessories like rings during the workout can lead to inaccurate detec on.
•Dry, moist or cold hands can influence the accuracy of detec on. It is recommended to keep moderate moisture on your hands and rub your hands for
keeping warm.
•Users with serious asthma, or atherosclerosis or peripheral arterial occlusive disease.
2)Unstable heart rate reading or the machine fails to display heart rate on the console display overview :
•Please make sure your skin have contact with the heart rate monitor. We recommend to wet the sensing area with clean water and try pairing again a er
wearing.
•Make sure the fastener of heart rate monitor sensor is securely fastened.
•Make sure the distance between the device and the receiver (on the upper right of onsole display overview) is within 300cm (118 in).
•Make sure the ba ery of heart rate monitor sensor is fully charged.
•Dry sensing area or loose strap of the heart rate monitor can effect detec on. It is necessary to maintain moderate moisture on the sensing area. Please
also make sure the strap fits your chest ghtly but comfortably.
Please follow the above-men oned steps to wear the heart rate monitor correctly and achieve the most accurate detec on during workout.
The heart rate monitor is an assis ve devices instead of a medical equipment. Please select the appropriate exercise intensity according to
your physical condi on.
Grounding Instruc on
Grounding
The power socket of this product contains a grounding conductor. This socket must be inserted into the outlet via the power cord with grounding latch. The plug must
be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.
Outlet
This product uses a rated voltage of 220V or 110V and comes with a three-pin power cord as shown in the following illustra on.
If the grounding outlet is not available, please use grounding adapter to connect this plug to the two-pin outlet. Please have qualified electrician install the
grounding outlet correctly before using the adapter. Please connect the grip or similar adapter extension to the ground and fix with the metal screw whenever
the adapter is used. Refer to the following illustra on.
Do determine the power cord is electrically related for 220V or 110V by checking the specifica on label or specifica on. Please make sure
the cord is connected to the plug with correct voltage. DO not use the power cord via adapter or extension cord to avoid of any component damage or personnel
injury caused by sudden voltage changes such as voltage surges and spikes.
Power cable
Three-pin outlet
•
The above illustra ons only show three-pin power code power cord and outlet or two-pin outlet and grounding adapter. The type of
three-prong, two-prong and grounding adapter may vary in different countries. The enclosed power cord will be provided according to local
regula ons of each country.
•
Make sure the power cord is connected to the outlet with correct voltage. DO NOT connect the power cord to the outlet via voltage adapter
or extension cord to avoid accidental current that may damage component and lead to personnel injury.
Exercise programs
P00
MANUAL
P01
INTERVAL 1-1
P02
INTERVAL 1-2
P03
WEIGHT LOSS
P04
HILL CLIMB
P05
CROSS COUNTRY
P06
TARGET LAP
P07
TARGRT STEP
P08
BASIC HRC 80/60%
P09
RUN/WALK 1-1
P10
RUN/WALK 1-2
P11
FATBURN
P12
MOUNTAIN RANGE
P13
HIKING TRAIL
P14
CLIMBING
P15
SPEED UP
Speaker
Water bo le holder
Handrail quick key
Handrail
Console display overview/opera ng panel
Safety key
Heart rate sensor bar
Motor safety guard
Side rail
Belt tension adjus ng screw
Caster
Two-pin outlet
Power cable
Metal grounding screw
Grounding adapter
Before Assembly
Enclosed tools
Hex wrench
Phillips screwdriver
Assembly parts
Console x 1
Display Console x 1
Upright x 2(L & R)
Upright safety cover x 2(L & R)
Accessory pack
Hardware parts box x 1
Safety key x 1
Power cable x 1
Line-level audio adapter x 1
Silicon oil x 1
Please contact the distribu-
tor or the Warranty card for
8
technical support if any part
is missing or you have any
ques on.
Step 1 of Assembly Procedure
Console cable
Console cable
B
B
B
B
C
C
C
C
C
C
D
D
A
A
C
C
D
D
A
A
Hex wrench
Hex wrench
Belt
• Put the console strut on the frame with great care to avoid any damage to the console cable.
• DO NOT lock the screw ghtly before you finish step 3.
Step 2 of Assembly Procedure
Step 3 of Assembly Procedure
C
A
C
A
A
C
B
A
C
B
D
D
A
B
• Please assemble the console with great care. Make sure no wire is pressed or bent to avoid any damage.
3
12
• Make sure all screws are well posi oned and lightly locked. DO NOT lock the screw ghtly when posi oning to ensure a smooth assembly.
No ces and safety ps
1) Please move and transport the treadmill carefully. Put the box on a level surface. Only open the box with its
surface on top. It is recommended to put a protec ve mat on the floor.
2) Unpack and assemble the treadmill at the planned loca on to avoid unnecessary transporta on. Pay great
a en on when unfastening cable e that used for packing or fixing to avoid accidental bounce.
3) Please follow assembly procedure to assemble the treadmill a er unfastening cable e. Please fold the machine
to upright and make sure the pin of hydraulic li
is securely locked if you need to li or move it. DO NOT try to
crane the machine.
4) DO NOT try to li or move the machine with a single part or stand. (Refer to "Move/transport the treadmill" on
P.14 for informa on related to moving the product.)
•
When assembling, make sure all nuts, screws and parts are posi oned and lightly locked before
proceeding to the next step. A er the assembly is completed, make sure all screws are securely
locked. DO NOT arbitrarily decrease the quan ty of assembling screw.
•
Several parts are lubricated before delivery to facilitate assembly. DO NOT arbitrarily wipe off the
lubricant. You can use lubricant to assemble parts when facing any difficulty. It is recommended
to use the lithium base grease for bike.
•
Several parts are very heavy; DO NOT try to assemble the machine on your own. These heavy
parts may fall and lead to personnal injury. Strongly recommend to have more than 2 persons for
assembly.
•
Please follow assembly instruc ons to li or move the treadmill. DO NOT arbitrarily li or take out
the product from the package.
•
Fail to following above instruc ons may lead to personnal injury and machine damage. Please
pay great a en on to these instruc ons.
Parts
Illustra on
A
B
C
D
B
B
C
C
1) Open hardware pack 1.
A
A
D
D
2) Connect the lead wire to the console cable, pull them through the
C
C
B
B
A
A
C
C
right upright of the console, pull out the lead wire from the right upright
D
D
C
C
and then fix the console cable to the top of upright. Please remove the
lead wire then.
3) Put the right upright on the frame.
4) Use part A, C & D (2 of each) and connect the upright to the frame.
Make sure all screws and washers are well posi oned and lock them
lightly.
5) Use part B & C (2 of each) and connect the upright to the frame. Make
sure part B & C are well posi oned and lightly locked. Confirm all screws
and washers on the right side are posi oned.
6) Repeat step 3~5 to complete the assembly of the le upright.
1) Take the le and right upright safety covers.
2) Put the protec ve cover through the right upright safety cover carefully.
3) Put the protec ve cover through the le upright safety cover carefully.
Parts
Illustra on
A
B
C
Console connec ng cable
D
1) Open hardware pack 3.
Console cable
2) Connect the console cable to the connec ng cable on the console.
D
A
D
A
3) Put the console on the uprights carefully.
Hex wrench
4) Use part A & C (2 of each for le and right side), connect the upright
to the frame. Make sure all screws and washers are well posi oned and
lock them lightly.
Phillips screwdriver
5) Use part A & D (2 of each for le and right side), connect the upright
B
to the frame. Make sure all screws and washers are well posi oned and
A
lock them lightly.
6) Li the uprights safety cover of the upright on both sides and lock all
screws at the lower side of upright ghtly.
7) Use part B (2pcs for le and right side) and lock the uprights safety
cover of the upright safety cover on both sides ghtly.
8) Lock all screws ghtly.
Hardware pack for step 1
Type
Descrip on
Qty
Screw
Bu on Head Socket Bolt (55L)
4
Screw
Bu on Head Socket Bolt (20L)
6
Washer
Flat washer (Ø23)
8
Washer
Split washer (Ø18)
4
Hardware pack for step 3
Type
Descrip on
Qty
Screw
Bu on Head Socket Bolt (20L)
8
Screw
Truss head Phillips screw (10L)
4
Washer
Flat washer (Ø23)
4
Washer
Curved washer (Ø23)
4