- ページ 2

自動車アクセサリー Atwood Lippert Components LEVELEGS MPD 66385のPDF マニュアルをオンラインで閲覧またはダウンロードできます。Atwood Lippert Components LEVELEGS MPD 66385 6 ページ。

ページを印刷する

3. Run shorter wires (

3-C & D) (butt connector at motor end) from

FIG

each of the front Direct Drive Landing Gear to control module.

Crimp opposite color wires to motor wires, red to yellow and yel-

low to red. At control module end cut wires to desired length,

strip wires back about 3/8˝ and crimp to appropriate butt connec-

tor on molex connector marked F (front) (

wire colors. Plug into control module connection marked front

(

10-R).

FIG

PREDELIVERY PREPARATION

Exit Error Mode State

Levelers are shipped in The Error Mode State. To take controls out of

the error mode state, complete an All Retract by following these steps.

1. Ensure slideout rooms are fully retracted (in their inboard posi-

tion) and the RV is supported other than on Levelers.

2. Switch Activation Switch to ON position (

button (

8-B) to turn unit on, Green LED'S should light up

FIG

under ON button.

3. Press and hold the RET/ALL buttons (

onds until the levelers begin to retract. The levelers will retract

to their fully retracted position, when completed the leveler

lights will all go to solid red (

Manually Position RV to Level

Note: If the RV is already in desired level position, then skip down

to To Set Auto Position.

1. Park the RV on a reasonably level site. Check for rocks, holes or

other obstructions. Warn all persons to stand clear of vehicle.

2. Do not extend the slideouts until RV is level.

3. Press EXT/ALL/FRONT to extend the front Landing Gear to the

ground (

8-J,G,C). Front position LED's will go to blinking

FIG

green when completed and the Wait LED will light while in process.

4. Press EXT/ALL/REAR to extend the rear levelers to the ground

(

8-J,G,F). Rear position leds will go to blinking green when

FIG

completed and the Wait LED will light while in process.

5. Press and hold EXT (or RET) (

(DRIVER, PASS, FRONT or REAR) (

desired position. Levelers always work in pairs.

To Set Auto position

1. Ensure RV is in the position you want. If not, then see Manually

Position RV to Level.

2. Ensure the Activation Switch is ON (

3. Press ON button (

8-B) turning the unit off. All LED's will go off.

FIG

4. Press EXT button (5) times (

5. Press RET button (5) times (

6. Unit will respond by blinking all leds slowly.

7. Press the ALL button (3) times (

8. Press RET/REAR to retract rear levelers (

rear leveler leds go solid green.

9. Press RET/FRONT to retract front landing gear (

sure the RV is supported or hooked up to Tow Vehicle and wait

until front leveler LED's go solid green.

Final Preparation

1. Wipe off any excess fluid from the top of the foot before deliv-

ery.

2. Run through Unhooking From Tow Vehicle and Leveling RV and

Hooking Up to Tow Vehicle to insure proper operation.

3. Check that the Activation Switch is in the OFF position (

This will keep the system from draining the battery.

OPERATION

PERSONAL INJURY

Stand clear of the vehicle.

•

VEHICLE CAN TIP

Soft/spongy ground may allow levelers to sink. Levelers must be on

•

firm solid and resonably level ground or surface prior to operation.

Insure area below and around leveler is clear of obstructions.

•

Do not place blocks under the leveler for additional ground clearance.

•

3-B) and matching

FIG

8-A). Press the ON

FIG

8-G&H) for 2-3 sec-

FIG

8-L).

FIG

8-H,J) and position button

FIG

8-C,D,E,F) to bring RV to

FIG

8-A).

FIG

8-J).

FIG

8-H).

FIG

8-G) and leds will stop blinking.

FIG

8-H,F). Wait until

FIG

8-H,C). Be

FIG

CAUTION

WARNING

Unhooking From Tow Vehicle and Leveling RV

1. Park RV on a reasonably level site with solid ground. Check for

rocks, holes or other obstructions at leveler positions. Chock RV

wheels and warn all persons to stand clear of RV and Tow Vehicle.

2. Do not extend the slideouts until RV is leveled.

3. Switch Activation Switch to ON (

4. Press ON to turn key pad on (

5. Press EXT/ALL/FRONT (

ground. LED's for front levelers will be blinking green to indicate

landing gear is down.

6. Press and hold EXT/FRONT (

get King-pin/Gooseneck into preferred hitch detachment position.

7. Detach trailer lights, harness and hitch using manufacturer's sug-

gested procedure. Move tow vehicle to safe position clear of RV.

8. Press AUTO (

FIG

Process will take 2-3 minutes and wait LED will be lit. All leveler

LED's will blink green when process complete.

9. Press the ON (

Activation Switch OFF (

These controls have the following features to facilitate leveling:

TO MAXIMIZE AVAILABLE LEVELER STROKE During the initial activation of

•

a pair of levelers following the

seconds the first pair of levelers extend, the opposite pair of levelers

will retract for two (2) seconds. This process will repeat for the first 60

continuous seconds of extension of first pair of levelers.

FULL EXTENSION If a leveler is fully extended, its corresponding LED

•

will indicate this and further operation of that pair of levelers in the

extend direction is prevented. If the switch is held on, the second lev-

eler of the pair will operate with its alternate pair partner leveler. (i.e.,

if the front two levelers are extending and the left front leveler

becomes fully extended, the right front leveler will continue to operate

and the right rear leveler will start to extend.) This is to keep the

frame from twisting.

LOAD COMPENSATION If one leveler becomes disproportionally more

•

loaded than its pair partner, power will shut off to the first leveler. The

second leveler will continue to operate until the load is more bal-

anced between the pair of levelers. Power to the first leveler will then

resume.

Hooking Up to Tow Vehicle / Retraction of Levelers

1. Have all slideout rooms retracted (in their inboard position) and

warn all persons to stand clear of RV.

2. Switch Activation Switch to ON (

3. Press ON to turn key pad on (

4. Press RET/REAR (

for rear levelers will go to solid green to indicate levelers are fully

retracted. A quick visual inspection should be done to check leveler

ground clearance is proper for safe towing.

5. Press and hold EXT/FRONT or RET/FRONT (

king-pin/gooseneck to proper hitch connection height.

6. Follow hitch manufacturer's hook-up procedure to tow vehicle and

connect trailer lights harness.

7. Once RV is safely connected to tow vehicle, press RET/FRONT (

7-A,C) to auto retract landing gear. LED's will go to solid green to

indicate landing gear is fully retracted. A quick visual check of land-

ing gear ground clearance should be done to insure safe towing.

8. Press ON button to turn power off and switch Activation Switch to

8-A).

FIG

OFF (

8-A).

FIG

9. Remove Chocks before towing.

Emergency Stop

Leveler extension or retraction in any auto function mode can be

stopped by pressing any button on the key pad. The controller will re-

enter most functions after an emergency stop. If not, retract all level-

ers and begin function from that point.

Do not move vehicle until levelers and landing legs are fully retracted.

•

Damage can occur to levelers, coach and surrounding property if the

•

levelers are not fully retracted prior to vehicle being moved.

8-A)

FIG

8-B). LED will light ON button.

FIG

8-J,G,C) to auto extend landing gear to

FIG

8-J,C) or RET/FRONT (

FIG

8-K) to extend rear levelers and auto-position RV.

8-B) button to turn key pad off and switch the

FIG

8-A) to minimize battery usage.

FIG

extend activation, for every six (6)

ALL

8-A).

FIG

8-B). LED will light ON button.

FIG

8-H,F) to auto retract the rear levelers. LED's

FIG

CAUTION

PRODUCT DAMAGE

8-H,C) to

FIG

8-J,H,C) to position

FIG