コントロールユニット Aube Technologies TH132 AのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Aube Technologies TH132 A 3 ページ。 Control module
Aube Technologies TH132 A にも：オーナーズマニュアル (3 ページ)

ページを印刷する

Control Module

TH132 A/F/AF

Owner's Guide

Thank you for choosing the Aube TH132, a programma-

ble thermostat that provides both energy savings and total

comfort.

Install the Control Module

Align the bracket tabs on the control module with the

holes located on top of the power base.

This control module must be installed on a PB130 series

power base.

Control module

Air vents

Power base

Note:

Keep the thermostat's air vents clean and free from

obstructions.

Note:

The screw cannot be removed completely.

TH132 Description

DAY/HOUR/MIN—Set the day and clock settings.

PGM—Program the schedule (programs).

MODE—Select the operating mode.

RETURN—To exit a function.

To configure temperature setpoints:

Comfort

Economy and

Adjust the floor temperature limit (AF only).

—Increase and decrease temperature.

—Indicates the number of the current

program when Automatic mode is enabled.

Current operating mode (auto

Auto mode, the program's associated setpoint icon is

also displayed (

Indicates the room OR floor temperature.

Heating indicators (see "Temperature Control"

below).

First Power ON

On the first installation, the screen displays:

0:00, MO,

and temperature (room/floor).

For Floor Heating Installations:

One of the two following messages may be dis-

played when a problem occurs:

Air vents

LO: The floor temperature is below 32°F (0°C), or

the temperature sensor is defective, or not

connected.

The heating indicator

is displayed and

the relay is closed (energized).

HI: The floor temperature is above

140°F (60°C), or the temperature sensor is

defective.

Set the Time and Day

Set the time (HOUR - MIN).

Set the day (DAY).

If you remove the module from its base for more than

2 hours, the time and day will have to be reprogrammed.

Models Overview

TH132-A

This model has been designed to control a room's ambi-

ent temperature.

The TH132-A has one temperature sensor located in the

control module.

TH132-AF

Vacation.

This model is designed to use a floor sensor to control the

room temperature.

The TH132-AF has two temperature sensors:

•

The first one, installed in the control module, controls

the ambient temperature.

•

The second one, installed in the floor (and connected

manual

). In

to the power base), limits the temperature of the floor

(the default setting of this limit is 82°F).

TH132-F

This model is designed to control floor heating systems.

The TH132-F has one temperature sensor installed in the

floor (sensor is connected to the power base).

Adjust the Temperature Setpoints

Comfort

and Economy

These setpoints are associated with the schedule's pro-

grams (prog. 1 & 3 = Comfort, prog. 2 & 4 = Economy)

and are preprogrammed as follows:

A & AF models—

F model—

82°F,

To modify a setpoint:

Set the temperature using

button until it is displayed on the screen.

Press MODE/RETURN to exit.

Vacation Setpoint

The vacation setpoint is associated to the Vacation oper-

ating mode and is preprogrammed to 50°F. To modify this

setpoint, repeat above steps.

Floor Temperature Setpoint (AF model only)

The floor temperature limit is preprogrammed to 82°F to

avoid damage to your floor.

To modify, press the adjustment button (below

pointed object, set the desired temperature using

press MODE/RETURN to exit.

Configure the Switches

The TH132 has two switches, located on the upper-left

part on the rear of the control module, which are used to

set the following options:

Early Start

When the Early Start function is enabled (disabled by

default), the TH132 calculates the optimum system start

time to obtain the desired temperature by the set time. To

enable this function:

Position switch #1 down.

Note:

When this function is enabled, the

system can be activated before the pro-

gram's start time.

Temperature Display

By default, the TH132 displays the temperature in °C. If

you wish to change to °F:

Position switch #2 up.

Note:

When you switch from °C to °F or vice

versa, the

redefined.

Select the Operating Mode

Setpoints

The TH132 offers three operating modes:

Automatic —

Press MODE to select

program number is displayed.

68°F,

64°F

You can temporarily bypass the current

68°F

program by setting a specific temperature setpoint

or by selecting one of the pre-defined setpoint

buttons (

and press and hold the

until the beginning of the next program.

Manual

Press MODE to select

Set temperature

defined setpoint buttons (

Vacation

during a prolonged absence.

Press

) using a

and

setpoints must be

Executes the schedule.

. The current

). The new setpoint will be maintained

—Maintains a constant temperature.

or select one of the pre-

—Maintains the Vacation setpoint

400-132-000-A