温度コントローラー Auber Instruments TD120-WのPDF 補足マニュアルをオンラインで閲覧またはダウンロードできます。Auber Instruments TD120-W 2 ページ。 Wireless temperature controller
Auber Instruments TD120-W にも：取扱説明書 (4 ページ)

ページを印刷する

AUBER INSTRUMENTS

Instruction Manual

1. Overview

Auber's TD120-W is a temperature controlling device with Wi-Fi network

connection capability. It has a build-in Wi-Fi module which allow its user to

monitor and control both temperature remotely from a smart phone or a tablet.

Once set up, user can access the data and change parameter settings even

the user is thousands of miles away from the device.

This guide provides an instruction on how to use AuberSmart app to connect to

the controller TD120-W. For basic operations of the controller, please check

the main manual of TD120.

2. Wireless connection

2.1. Specifications

Frequency Range

Standards

Output Power

Receiving

Sensitivity

Data Rates

11 M @ 802.11b, 54 M @ 802.11g, MCS7 @ 802.11n

Encryption Standards: WEP/WEPA/WPA2

Security

Encryption Algorithms: WEP64/WEP128/TKIP/AES

Wi-Fi Type

Note

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation. TD120-W contains radio

module. FCC ID: 2ACDZ-3301-SBSL.

2.2. Requirements

•

User must have a smart phone/tablet with AuberSmart app installed

(available for Android 4.4 or above and for iOS 10).

•

User must have a Wi-Fi network, the network's name (SSID) and

the password.

•

During the initial set up, user's smart phone/tablet must connect to

the designated Wi-Fi network.

•

The device must under the coverage of the designated Wi-Fi

network all the time.

2.3. Wireless connection indicator

There is a blue LED indicator shows the status of the wireless connection. It is

located at the lower right corner of the display window. Different blinking

frequency indicates different communication status. Normally, this indicator is

OFF.

Fast blinking (4 Hz): initializing/reset wireless connection.

Slow blinking (0.5 Hz): wireless signal out-of-range; device lost wireless

connection.

2019.08

Supplementary Manual for TD120-W

Wireless Temperature Controller

Version 1.0 (August, 2019)

2.412 GHz - 2.484 GHz

802.11b/g/n

802.11b: 16 dBm

802.11g: 14 dBm

802.11n: 13 dBm

802.11b < -78 dBm

802.11g < -68 dBm

802.11n < -66 dBm

STA/AP

Short single or multiple pulses: device is communicating with user's

phone/tablet.

2.4. Initial set up

When the device is first power up, the wireless connection indicator will fast

blink, which means the device is not connected to any Wi-Fi signal yet. User

can configure the device from his/her smart phone/tablet if AuberSmart app is

installed. The indicator will stop blinking after wireless connection is set up. Or

if user hasn't set up the wireless connection during the first 30 min, the

indicator will also stop blinking. User will have to reset the Wi-Fi module when

he/she wants to re-configure the wireless connection.

2.5. Reset wireless connection

If the device TD120-W was configured to a Wi-Fi signal and later it was taken

to a new place that is not under the coverage of the Wi-Fi signal, the wireless

module must be reset.

Place the device under the coverage of the new Wi-Fi signal. When

the device is powered up, the blue indicator will start blinking slowly

(0.5 Hz) due to the original Wi-Fi signal is out-of-range.

On the device, hold both SET key and Down Arrow ( ▼) key for 2

seconds till the blue LED start fast blinking (4 Hz).

On your AuberSmart app, delete this device if it is still on the device

list. Then proceed to add a new device. A step by step instruction

can be found in section 4.

Note

After reset the wireless connection, other users need to delete the device from

Device List and add it back to their AuberSmart app again, but they don't need

to reset the Wi-Fi module on the device. If other users don't delete the device

and re-configure it, they may still be able to connect to the device when their

phones and device are both in the original Wi-Fi network. But they won't be

able to connect the device once when they leave the Wi-Fi network.

3. Getting started

1) Download and install the latest AuberSmart app. The app can be found

in Google Play (for Android users) or from Apple Store (for iOS user).

The Android version app can also be downloaded as the apk file from

Auber's website.

2) Take the device to a location that is under the coverage of a Wi-Fi

network signal which you have its name (SSID) and the password.

Power up the device and you should see the blue indicator start blinking.

3) Make sure you have turned on the Wi-Fi connection in smart

phone/tablet, and make sure it is connected to the Wi-Fi signal that you

have the password. You can go to "Settings", then "Wi-Fi" in your

phone/tablet to set it up.

4) Add a new device. Open the AuberSmart app, at "Device list" page, click

the plus icon "+" on the top right corner to add a new.

5) On the Add Device page, enter your current Wi-Fi network name (SSID)

and then type in your password. If the SSID doesn't show up

automatically or correctly, please manually enter the correct SSID. Once

WWW.AUBERINS.COM

P1/2